powerpc: remove icecube_5200, Lite5200, cpci5200, mecp5200, pf5200

These boards are still non-generic boards.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>

1 files changed, 0 insertions, 326 deletions

diff --git a/board/icecube/icecube.c b/board/icecube/icecube.c
deleted file mode 100644
index f0af24ad9b..0000000000
--- a/board/icecube/icecube.c
+++ /dev/null
@@ -1,326 +0,0 @@
-/*
- * (C) Copyright 2003
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2004
- * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc5xxx.h>
-#include <pci.h>
-#include <asm/processor.h>
-#include <libfdt.h>
-#include <netdev.h>
-
-#if defined(CONFIG_LITE5200B)
-#include "mt46v32m16.h"
-#else
-# if defined(CONFIG_MPC5200_DDR)
-#  include "mt46v16m16-75.h"
-# else
-#include "mt48lc16m16a2-75.h"
-# endif
-#endif
-
-#ifdef CONFIG_LITE5200B_PM
-/* u-boot part of low-power mode implementation */
-#define SAVED_ADDR (*(void **)0x00000000)
-#define PSC2_4 0x02
-
-void lite5200b_wakeup(void)
-{
-	unsigned char wakeup_pin;
-	void (*linux_wakeup)(void);
-
-	/* check PSC2_4, if it's down "QT" is signaling we have a wakeup
-	 * from low power mode */
-	*(vu_char *)MPC5XXX_WU_GPIO_ENABLE = PSC2_4;
-	__asm__ volatile ("sync");
-
-	wakeup_pin = *(vu_char *)MPC5XXX_WU_GPIO_DATA_I;
-	if (wakeup_pin & PSC2_4)
-		return;
-
-	/* acknowledge to "QT"
-	 * by holding pin at 1 for 10 uS */
-	*(vu_char *)MPC5XXX_WU_GPIO_DIR = PSC2_4;
-	__asm__ volatile ("sync");
-	*(vu_char *)MPC5XXX_WU_GPIO_DATA_O = PSC2_4;
-	__asm__ volatile ("sync");
-	udelay(10);
-
-	/* put ram out of self-refresh */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL |= 0x80000000;	/* mode_en */
-	__asm__ volatile ("sync");
-	*(vu_long *)MPC5XXX_SDRAM_CTRL |= 0x50000000;	/* cke ref_en */
-	__asm__ volatile ("sync");
-	*(vu_long *)MPC5XXX_SDRAM_CTRL &= ~0x80000000;	/* !mode_en */
-	__asm__ volatile ("sync");
-	udelay(10); /* wait a bit */
-
-	/* jump back to linux kernel code */
-	linux_wakeup = SAVED_ADDR;
-	printf("\n\nLooks like we just woke, transferring control to 0x%08lx\n",
-			(unsigned long)linux_wakeup);
-	linux_wakeup();
-}
-#else
-#define lite5200b_wakeup()
-#endif
-
-#ifndef CONFIG_SYS_RAMBOOT
-static void sdram_start (int hi_addr)
-{
-	long hi_addr_bit = hi_addr ? 0x01000000 : 0;
-
-	/* unlock mode register */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000000 | hi_addr_bit;
-	__asm__ volatile ("sync");
-
-	/* precharge all banks */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
-	__asm__ volatile ("sync");
-
-#if SDRAM_DDR
-	/* set mode register: extended mode */
-	*(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_EMODE;
-	__asm__ volatile ("sync");
-
-	/* set mode register: reset DLL */
-	*(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE | 0x04000000;
-	__asm__ volatile ("sync");
-#endif
-
-	/* precharge all banks */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
-	__asm__ volatile ("sync");
-
-	/* auto refresh */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000004 | hi_addr_bit;
-	__asm__ volatile ("sync");
-
-	/* set mode register */
-	*(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE;
-	__asm__ volatile ("sync");
-
-	/* normal operation */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | hi_addr_bit;
-	__asm__ volatile ("sync");
-}
-#endif
-
-/*
- * ATTENTION: Although partially referenced initdram does NOT make real use
- *            use of CONFIG_SYS_SDRAM_BASE. The code does not work if CONFIG_SYS_SDRAM_BASE
- *            is something else than 0x00000000.
- */
-
-phys_size_t initdram (int board_type)
-{
-	ulong dramsize = 0;
-	ulong dramsize2 = 0;
-	uint svr, pvr;
-
-#ifndef CONFIG_SYS_RAMBOOT
-	ulong test1, test2;
-
-	/* setup SDRAM chip selects */
-	*(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x0000001e;/* 2G at 0x0 */
-	*(vu_long *)MPC5XXX_SDRAM_CS1CFG = 0x80000000;/* disabled */
-	__asm__ volatile ("sync");
-
-	/* setup config registers */
-	*(vu_long *)MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
-	*(vu_long *)MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
-	__asm__ volatile ("sync");
-
-#if SDRAM_DDR
-	/* set tap delay */
-	*(vu_long *)MPC5XXX_CDM_PORCFG = SDRAM_TAPDELAY;
-	__asm__ volatile ("sync");
-#endif
-
-	/* find RAM size using SDRAM CS0 only */
-	sdram_start(0);
-	test1 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
-	sdram_start(1);
-	test2 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
-	if (test1 > test2) {
-		sdram_start(0);
-		dramsize = test1;
-	} else {
-		dramsize = test2;
-	}
-
-	/* memory smaller than 1MB is impossible */
-	if (dramsize < (1 << 20)) {
-		dramsize = 0;
-	}
-
-	/* set SDRAM CS0 size according to the amount of RAM found */
-	if (dramsize > 0) {
-		*(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x13 + __builtin_ffs(dramsize >> 20) - 1;
-	} else {
-		*(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */
-	}
-
-	/* let SDRAM CS1 start right after CS0 */
-	*(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize + 0x0000001e;/* 2G */
-
-	/* find RAM size using SDRAM CS1 only */
-	if (!dramsize)
-		sdram_start(0);
-	test2 = test1 = get_ram_size((long *)(CONFIG_SYS_SDRAM_BASE + dramsize), 0x80000000);
-	if (!dramsize) {
-		sdram_start(1);
-		test2 = get_ram_size((long *)(CONFIG_SYS_SDRAM_BASE + dramsize), 0x80000000);
-	}
-	if (test1 > test2) {
-		sdram_start(0);
-		dramsize2 = test1;
-	} else {
-		dramsize2 = test2;
-	}
-
-	/* memory smaller than 1MB is impossible */
-	if (dramsize2 < (1 << 20)) {
-		dramsize2 = 0;
-	}
-
-	/* set SDRAM CS1 size according to the amount of RAM found */
-	if (dramsize2 > 0) {
-		*(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize
-			| (0x13 + __builtin_ffs(dramsize2 >> 20) - 1);
-	} else {
-		*(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize; /* disabled */
-	}
-
-#else /* CONFIG_SYS_RAMBOOT */
-
-	/* retrieve size of memory connected to SDRAM CS0 */
-	dramsize = *(vu_long *)MPC5XXX_SDRAM_CS0CFG & 0xFF;
-	if (dramsize >= 0x13) {
-		dramsize = (1 << (dramsize - 0x13)) << 20;
-	} else {
-		dramsize = 0;
-	}
-
-	/* retrieve size of memory connected to SDRAM CS1 */
-	dramsize2 = *(vu_long *)MPC5XXX_SDRAM_CS1CFG & 0xFF;
-	if (dramsize2 >= 0x13) {
-		dramsize2 = (1 << (dramsize2 - 0x13)) << 20;
-	} else {
-		dramsize2 = 0;
-	}
-
-#endif /* CONFIG_SYS_RAMBOOT */
-
-	/*
-	 * On MPC5200B we need to set the special configuration delay in the
-	 * DDR controller. Please refer to Freescale's AN3221 "MPC5200B SDRAM
-	 * Initialization and Configuration", 3.3.1 SDelay--MBAR + 0x0190:
-	 *
-	 * "The SDelay should be written to a value of 0x00000004. It is
-	 * required to account for changes caused by normal wafer processing
-	 * parameters."
-	 */
-	svr = get_svr();
-	pvr = get_pvr();
-	if ((SVR_MJREV(svr) >= 2) &&
-	    (PVR_MAJ(pvr) == 1) && (PVR_MIN(pvr) == 4)) {
-
-		*(vu_long *)MPC5XXX_SDRAM_SDELAY = 0x04;
-		__asm__ volatile ("sync");
-	}
-
-	lite5200b_wakeup();
-
-	return dramsize + dramsize2;
-}
-
-int checkboard (void)
-{
-#if defined (CONFIG_LITE5200B)
-	puts ("Board: Freescale Lite5200B\n");
-#else
-	puts ("Board: Motorola MPC5200 (IceCube)\n");
-#endif
-	return 0;
-}
-
-void flash_preinit(void)
-{
-	/*
-	 * Now, when we are in RAM, enable flash write
-	 * access for detection process.
-	 * Note that CS_BOOT cannot be cleared when
-	 * executing in flash.
-	 */
-	*(vu_long *)MPC5XXX_BOOTCS_CFG &= ~0x1; /* clear RO */
-}
-
-void flash_afterinit(ulong size)
-{
-	if (size == 0x800000) { /* adjust mapping */
-		*(vu_long *)MPC5XXX_BOOTCS_START = *(vu_long *)MPC5XXX_CS0_START =
-			START_REG(CONFIG_SYS_BOOTCS_START | size);
-		*(vu_long *)MPC5XXX_BOOTCS_STOP = *(vu_long *)MPC5XXX_CS0_STOP =
-			STOP_REG(CONFIG_SYS_BOOTCS_START | size, size);
-	}
-}
-
-#ifdef	CONFIG_PCI
-static struct pci_controller hose;
-
-extern void pci_mpc5xxx_init(struct pci_controller *);
-
-void pci_init_board(void)
-{
-	pci_mpc5xxx_init(&hose);
-}
-#endif
-
-#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_RESET)
-
-void init_ide_reset (void)
-{
-	debug ("init_ide_reset\n");
-
-	/* Configure PSC1_4 as GPIO output for ATA reset */
-	*(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC1_4;
-	*(vu_long *) MPC5XXX_WU_GPIO_DIR    |= GPIO_PSC1_4;
-	/* Deassert reset */
-	*(vu_long *) MPC5XXX_WU_GPIO_DATA_O   |= GPIO_PSC1_4;
-}
-
-void ide_set_reset (int idereset)
-{
-	debug ("ide_reset(%d)\n", idereset);
-
-	if (idereset) {
-		*(vu_long *) MPC5XXX_WU_GPIO_DATA_O &= ~GPIO_PSC1_4;
-		/* Make a delay. MPC5200 spec says 25 usec min */
-		udelay(500000);
-	} else {
-		*(vu_long *) MPC5XXX_WU_GPIO_DATA_O |=  GPIO_PSC1_4;
-	}
-}
-#endif
-
-#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
-int ft_board_setup(void *blob, bd_t *bd)
-{
-	ft_cpu_setup(blob, bd);
-
-	return 0;
-}
-#endif
-
-int board_eth_init(bd_t *bis)
-{
-	cpu_eth_init(bis); /* Built in FEC comes first */
-	return pci_eth_init(bis);
-}