| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| | |
|
| | |
|
| |
|
|
| |
If some interfaces are given on the commandline, ignore all others.
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This did not really work out as we had hoped. Trying to do this upstream
introduced several problems that probably makes it better suited as a
downstream patch after all. At any rate, it is not releaseable in the
current state, so we at least need to revert this before the release.
* by adjusting the path to binaries, but not do the same thing to the
search path we end up with inconsistent man-pages. Adjusting the search
path too would be quite messy, and it is not at all obvious that this is
worth the effort, but at any rate it would have to be done before we
could ship this.
* this means that distributed man-pages does not make sense as they depend
on config options, and for better or worse we are still distributing
man pages, so that is something that definitely needs sorting out before
we could ship with this patch.
* we have long held that split-usr is only minimally supported in order
to boot, and something we hope will eventually go away. So before we start
adding even more magic/effort in order to make this work nicely, we should
probably question if it makes sense at all.
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In particular, use /lib/systemd instead of /usr/lib/systemd in distributions
like Debian which still have not adopted a /usr merge setup.
Use XML entities from man/custom-entities.ent to replace configured paths while
doing XSLT processing of the original XML files. There was precedent of some
files (such as systemd.generator.xml) which were already using this approach.
This addresses most of the (manual) fixes from this patch:
http://anonscm.debian.org/cgit/pkg-systemd/systemd.git/tree/debian/patches/Fix-paths-in-man-pages.patch?h=experimental-220
The idea of using generic XML entities was presented here:
http://lists.freedesktop.org/archives/systemd-devel/2015-May/032240.html
This patch solves almost all the issues, with the exception of:
- Path to /bin/mount and /bin/umount.
- Generic statements about preference of /lib over /etc.
These will be handled separately by follow up patches.
Tested:
- With default configure settings, ran "make install" to two separate
directories and compared the output to confirm they matched exactly.
- Used a set of configure flags including $CONFFLAGS from Debian:
http://anonscm.debian.org/cgit/pkg-systemd/systemd.git/tree/debian/rules
Installed the tree and confirmed the paths use /lib/systemd instead of
/usr/lib/systemd and that no other unexpected differences exist.
- Confirmed that `make distcheck` still passes.
|
| | |
|
| |
|
|
|
| |
Default to timing out after 120 seconds without a network connection. Setting a
timeout of 0 disables the timeout.
|
| |
|
|
|
|
| |
In addition to the loopback device, also explicitly configured devices to be ignored.
Suggested by Charles Devereaux <systemd@guylhem.net>.
|
| |
|
|
|
| |
Set commas where there should be some.
Some improvements to word order.
|
| | |
|
| | |
|
|
|
To make sure we don't delay boot on systems where (some) network links are managed by someone else
we don't block if something else has successfully brought up a link.
We will still block until all links we are aware of that are managed by networkd have been
configured, but if no such links exist, and someone else have configured a link sufficiently
that it has a carrier, it may be that the link is ready so we should no longer block.
Note that in all likelyhood the link is not ready (no addresses/routes configured),
so whatever network managment daemon configured it should provide a similar wait-online
service to block network-online.target until it is ready.
The aim is to block as long as we know networking is not fully configured, but no longer. This
will allow systemd-networkd-wait-online.service to be enabled on any system, even if we don't
know whether networkd is the main/only network manager.
Even in the case networking is fully configured by networkd, the default behavior may not be
sufficient: if two links need to be configured, but the first is fully configured before the
second one appears we will assume the network is up. To work around that, we allow specifying
specific devices to wait for before considering the network up.
This unit is enabled by default, just like systemd-networkd, but will only be pulled in if
anyone pulls in network-online.target.
|
