summaryrefslogtreecommitdiff
path: root/arch/arm/mach-mx6/board-mx6solo_sabreauto.h
Commit message (Collapse)AuthorAgeFilesLines
* ENGR00259693 MX6DL/S-Enable routing of ENET interrupt to GPIORanjani Vaidyanathan2013-04-221-1/+5
| | | | | | | | | | | | In order to fix the performance issue on ENET when WAIT mode is activated, route the ENET interrupts to a GPIO on all MX6DL boards. This patch must be applied on top of: MX6Q/DL-Fix Ethernet performance issue when WAIT mode is active 808863866d2c17aeb3e70a7fcd094bd96db4b601 bae4d40849f3acdd9663f5a0857c9415ed7e6d5d Signed-off-by: Ranjani Vaidyanathan <ra5478@freescale.com>
* ENGR00225875-1 i.MX6Q/Solo SabreAuto Infineon Bluetooth uart3 configIsrael Perez2012-11-051-3/+10
| | | | | | | | | | | | | | Configure MUX settings for bluetooth operation over UART3. Enable RTS,CTS and DMA only for uart3. Affected files : arch/arm/mach-mx6/board-mx6q_sabreauto.c arch/arm/mach-mx6/board-mx6q_sabreauto.h arch/arm/mach-mx6/board-mx6solo_sabreauto.h arch/arm/plat-mxc/include/mach/iomux-mx6q.h On behalf of Francisco Munoz <francisco.munoz@freescale.com>. Some modification are needed also on hciattach tool. Signed-off-by: Israel Perez <B37753@freescale.com>
* ENGR00231063 Sabreauto: fix share pins SD Card and NFCAlejandro Sierra2012-10-291-2/+0
| | | | | | | | | SD card card detection and NFC controller CS2 share the same pin on ARD platform. However CS2 is not connected to the socket. This signal was removed from the sabreauto board file. Signed-off-by: Alejandro Sierra <b18039@freescale.com>
* ENGR00224886 board-mx6q-sabreauto: remove camera control linesAdrian Alonso2012-09-181-4/+0
| | | | | | | | | * Remove camera control lines, this gpio control lines are used by other periherals * GPIO_4_5 correspond to RGMII_INT * GPIO_3_24 correspond to CSI0_DAT5 parallel tv-in Signed-off-by: Adrian Alonso <aalonso@freescale.com>
* ENGR00215870-1 board-mx6 sabreauto rev B add extra padsAdrian Alonso2012-09-031-3/+4
| | | | | | | * For rev_b target board add extra pads table, separate pad definitions from I2C3 pad array Signed-off-by: Adrian Alonso <aalonso@freescale.com>
* ENGR00219139: imx6 Sabreauto HDMI DDC I2C writing errorAdrian Alonso2012-08-021-2/+2
| | | | | | | | | | * imx6 Sabreauto HDMI DDC configuration causes I2C writing error * Fix with HDMI, I2C2 SCL pad configuration for SABRE-AI MX6Q_PAD_EIM_EB2__HDMI_TX_DDC_SCL MX6Q_PAD_EIM_EB2__I2C2_SCL Signed-off-by: Adrian Alonso <aalonso@freescale.com>
* ENGR00213014-2 MX6x Sabreauto: IOMUX setting for HDMI HDCP functionSandor Yu2012-07-201-0/+10
| | | | | | | Added enable_pins/disable_pins functions for Mx6q/dl sabreauto HDMI. Added HDMI DDC IOMUX setting. Signed-off-by: Sandor Yu <R01008@freescale.com>
* ENGR00213293 : Enable WEIM NOR support on the imx6 ARD revb quad/solo.Francisco Munoz2012-07-201-64/+68
| | | | | | | | | | | | | | | | Added IOMUX,GPIO and early param support for the parallel nor to work on the imx6 revB quad/solo. Since the parallel NOR can clash with I2C3, and SPI, an early param was added to enable WEIM NOR chips using boot args. The Weim NOR needs a HW rework for it to work. This rework is going to disable the SPI NOR. Modified files: arch/arm/mach-mx6/board-mx6q_sabreauto.c arch/arm/mach-mx6/board-mx6q_sabreauto.h arch/arm/mach-mx6/board-mx6solo_sabreauto.h Signed-off-by: Francisco Munoz <francisco.munoz@freescale.com>
* ENGR00179129 Board support for I2C AMFM module for IMX6Q and IMX6DLAlejandro Sierra2012-07-201-0/+5
| | | | | | | | | Modifications in ARD board file to support the Audio for AMFM module for IMX6Q and IMX6DL (REV A and REV B) Supported for kernel 3.0.15. Also it contains the I2C configuration for the AMFM module. Signed-off-by: Alejandro Sierra <b18039@freescale.com>
* ENGR00178584 uart3 pins configurationAlejandro Sierra2012-07-201-0/+3
| | | | | | | | | Uart 3 and NFC pins are shared. Uart 3 enablement is done by passing an early parameter called "uart3" from uboot. Both interfaces (Uart3 and NFC) can NOT coexist on the same configuration at the same time. Signed-off-by: Alejandro Sierra <b18039@freescale.com>
* ENGR00177643: Add mlb initial code to mx6 ard boardTerry Lv2012-07-201-0/+5
| | | | | | Add mlb initial code to mx6 ard board. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00177787 mx6 sabreauto: add light sensor isl29023 supportLily Zhang2012-07-201-1/+2
| | | | | | Add light sensor isl29023 support Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00177716 i.mx Sabreauto : SD Card on Mainboard initialisation and read errorPrabhu Sundararaj2012-07-201-6/+6
| | | | | | | SD Card in main board takes a long route hence with Drive Speed High 80 OHMS causing error. Per suggestion DSE 40 OHMS is used. Signed-off-by: Prabhu Sundararaj <b36876@freescale.com>
* ENGR00177154 solo sabreauto: config USB pin according to boardmake shi2012-07-201-1/+1
| | | | | | config the USB pin and power control for ARD board Signed-off-by: make shi <b15407@freescale.com>
* ENGR00176812-9 mx6 sabreauto: add revB board supportAdrian Alonso2012-07-201-2/+12
| | | | | | | | | | | | | * mx6 sabreauto revB include a steering logic circuit that enables the route path for i2c3_sda signal. This patch enables i2c3_sda route to fix io-expander read/write errors and additional devices connected to the i2c3 bus. * mx6 sabreauto revB board uses atheors fec phy. * Set GPIO_16 as input for IEEE-1588 ts_clk and RMII reference clk Signed-off-by: Adrian Alonso <aalonso@freescale.com>
* ENGR00176812-7 mx6 sabreauto: remove MX6Q_PAD_EIM_EB2__GPIO_2_30Lily Zhang2012-07-201-3/+3
| | | | | | | | - EIM_EB2 is used as I2C2_SCL instead of GPIO for SPI NOR for RevA board - Use CONFIG_MTD_M25P80 to control SPI NOR code only Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00176812-5 i.mx6: sabreauto: add the i.mx6solo pad tableJason Liu2012-07-201-0/+333
Add the i.mx6solo pad table Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Lily Zhang <r58066@freescale.com>
View Lorry Controller Status