1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
|
@c This is part of the Emacs manual.
@c Copyright (C) 1985, 86, 87, 93, 94, 95, 1997 Free Software Foundation, Inc.
@c See file emacs.texi for copying conditions.
@node M-x, Help, Minibuffer, Top
@chapter Running Commands by Name
The Emacs commands that are used often or that must be quick to type are
bound to keys---short sequences of characters---for convenient use. Other
Emacs commands that do not need to be brief are not bound to keys; to run
them, you must refer to them by name.
A command name is, by convention, made up of one or more words,
separated by hyphens; for example, @code{auto-fill-mode} or
@code{manual-entry}. The use of English words makes the command name
easier to remember than a key made up of obscure characters, even though
it is more characters to type.
@kindex M-x
The way to run a command by name is to start with @kbd{M-x}, type the
command name, and finish it with @key{RET}. @kbd{M-x} uses the
minibuffer to read the command name. @key{RET} exits the minibuffer and
runs the command. The string @samp{M-x} appears at the beginning of the
minibuffer as a @dfn{prompt} to remind you to enter the name of a
command to be run. @xref{Minibuffer}, for full information on the
features of the minibuffer.
You can use completion to enter the command name. For example, the
command @code{forward-char} can be invoked by name by typing
@example
M-x forward-char @key{RET}
@end example
@noindent
or
@example
M-x forw @key{TAB} c @key{RET}
@end example
@noindent
Note that @code{forward-char} is the same command that you invoke with
the key @kbd{C-f}. You can run any Emacs command by name using
@kbd{M-x}, whether or not any keys are bound to it.
If you type @kbd{C-g} while the command name is being read, you cancel
the @kbd{M-x} command and get out of the minibuffer, ending up at top level.
To pass a numeric argument to the command you are invoking with
@kbd{M-x}, specify the numeric argument before the @kbd{M-x}. @kbd{M-x}
passes the argument along to the command it runs. The argument value
appears in the prompt while the command name is being read.
@vindex suggest-key-bindings
If the command you type has a key binding of its own, Emacs mentions
this in the echo area, two seconds after the command finishes (if you
don't type anything else first). For example, if you type @kbd{M-x
forward-word}, the message says that you can run the same command more
easily by typing @kbd{M-f}. You can turn off these messages by setting
@code{suggest-key-bindings} to @code{nil}.
Normally, when describing in this manual a command that is run by
name, we omit the @key{RET} that is needed to terminate the name. Thus
we might speak of @kbd{M-x auto-fill-mode} rather than @kbd{M-x
auto-fill-mode @key{RET}}. We mention the @key{RET} only when there is
a need to emphasize its presence, such as when we show the command
together with following arguments.
@findex execute-extended-command
@kbd{M-x} works by running the command
@code{execute-extended-command}, which is responsible for reading the
name of another command and invoking it.
|
