1 files changed, 18 insertions, 67 deletions
diff --git a/gas/doc/as.texi b/gas/doc/as.texi
index ab661a73dbe..fa155096159 100644
--- a/gas/doc/as.texi
+++ b/gas/doc/as.texi
@@ -631,6 +631,11 @@ gcc(1), ld(1), and the Info entries for @file{binutils} and @file{ld}.
 
 @emph{Target Z80 options:}
   [@b{-z80}]|[@b{-z180}]|[@b{-r800}]|[@b{-ez80}]|[@b{-ez80-adl}]
+  [@b{-local-prefix=}@var{PREFIX}]
+  [@b{-colonless}]
+  [@b{-sdcc}]
+  [@b{-fp-s=}@var{FORMAT}]
+  [@b{-fp-d=}@var{FORMAT}]
   [@b{-strict}]|[@b{-full}]
   [@b{-with-inst=@var{INST}[,...]}] [@b{-Wnins @var{INST}[,...]}]
   [@b{-without-inst=@var{INST}[,...]}] [@b{-Fins @var{INST}[,...]}]
@@ -1940,78 +1945,24 @@ Xtensa processor.
 
 @end ifset
 
-@c man begin OPTIONS
-
 @ifset Z80
-The following options are available when @value{AS} is configured for
-a Z80 family processor.
-@table @gcctabopt
 
-@item -z80
-Assemble for Z80 processor.
-@item -r800
-Assemble for R800 processor.
-@item -z180
-Assemble for Z180 processor.
-@item -ez80
-Assemble for eZ80 processor in Z80 memory mode by default.
-@item -ez80-adl
-Assemble for eZ80 processor in ADL memory mode by default.
-
-@item  @code{-colonless}
-Accept colonless labels. All names at line begin are treated as labels.
-@item  @code{-sdcc}
-Accept assembler code produces by SDCC.
-
-@item  @code{-strict}
-Accept documented instructions only.
-@item  @code{-full}
-Accept all known Z80 instructions.
-@item  @code{-with-inst=INST[,...]}
-@itemx @code{-Wnins INST[,...]}
-Enable specified undocumented instruction(s).
-@item  @code{-without-inst=INST[,...]}
-@itemx @code{-Fins INST[,...]}
-Disable specified undocumented instruction(s).
-
-@item  -ignore-undocumented-instructions
-@itemx -Wnud
-Assemble undocumented Z80 instructions that also work on R800 without warning.
-@item  -ignore-unportable-instructions
-@itemx -Wnup
-Assemble all undocumented Z80 instructions without warning.
-@item  -warn-undocumented-instructions
-@itemx -Wud
-Issue a warning for undocumented Z80 instructions that also work on R800.
-@item  -warn-unportable-instructions
-@itemx -Wup
-Issue a warning for undocumented Z80 instructions that do not work on R800.
-@item  -forbid-undocumented-instructions
-@itemx -Fud
-Treat all undocumented instructions as errors.
-@item  -forbid-unportable-instructions
-@itemx -Fup
-Treat undocumented Z80 instructions that do not work on R800 as errors.
-@end table
+@ifclear man
+@xref{Z80 Options}, for the options available when @value{AS} is configured
+for an Z80 processor.
+@end ifclear
 
-Folowing undocumented instructions may be enabled/disabled by
-@code{-with-inst}/@code{-without-inst}:
-@table @gcctabopt
-@item  @code{idx-reg-halves}
-All operations with halves of index registers (IXL, IXH, IYL, IYH).
-@item  @code{sli}
-SLI or SLL instruction.
-@item  @code{op-ii-ld}
-Istructions like @code{<op> (<ii>+<d>),<r>}, where @code{<op>}
-is shift or bit manipulation instruction (RLC, SLA, SET, RES...).
-@item @code{in-f-c}
-Instruction @code{IN F,(C)}.
-@item @code{out-c-0}
-Instruction @code{OUT (C),0}
-@end table
+@ifset man
+@c man begin OPTIONS
+The following options are available when @value{AS} is configured for an
+Z80 processor.
+@c man end
+@c man begin INCLUDE
+@include c-z80.texi
+@c ended inside the included file
 @end ifset
 
-@c man end
+@end ifset
 
 @menu
 * Manual::                      Structure of this Manual