/* SPDX-License-Identifier: GPL-2.0+ */ /* * Configuation settings for the BuS EB+CPU5283 boards (aka EB+MCF-EV123) * * (C) Copyright 2005-2009 BuS Elektronik GmbH & Co.KG */ #ifndef _CONFIG_EB_CPU5282_H_ #define _CONFIG_EB_CPU5282_H_ #undef CONFIG_SYS_HALT_BEFOR_RAM_JUMP /*----------------------------------------------------------------------* * High Level Configuration Options (easy to change) * *----------------------------------------------------------------------*/ #define CONFIG_SYS_UART_PORT (0) #undef CONFIG_MONITOR_IS_IN_RAM /* starts uboot direct */ /*----------------------------------------------------------------------* * Options * *----------------------------------------------------------------------*/ #define STATUS_LED_ACTIVE 0 /*----------------------------------------------------------------------* * Configuration for environment * * Environment is in the second sector of the first 256k of flash * *----------------------------------------------------------------------*/ /*#define CONFIG_SYS_DRAM_TEST 1 */ #undef CONFIG_SYS_DRAM_TEST /*----------------------------------------------------------------------* * Clock and PLL Configuration * *----------------------------------------------------------------------*/ #define CONFIG_SYS_CLK 80000000 /* 8MHz * 8 */ /* PLL Configuration: Ext Clock * 8 (see table 9-4 of MCF user manual) */ #define CONFIG_SYS_MFD 0x02 /* PLL Multiplication Factor Devider */ #define CONFIG_SYS_RFD 0x00 /* PLL Reduce Frecuency Devider */ /*----------------------------------------------------------------------* * Network * *----------------------------------------------------------------------*/ #ifdef CONFIG_MCFFEC #define CONFIG_OVERWRITE_ETHADDR_ONCE #endif /*------------------------------------------------------------------------- * Low Level Configuration Settings * (address mappings, register initial values, etc.) * You should know what you are doing if you make changes here. *-----------------------------------------------------------------------*/ #define CONFIG_SYS_MBAR 0x40000000 /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in DPRAM) *-----------------------------------------------------------------------*/ #define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 #define CONFIG_SYS_INIT_RAM_SIZE 0x10000 /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ #define CONFIG_SYS_SDRAM_BASE0 0x00000000 #define CONFIG_SYS_SDRAM_SIZE0 16 /* SDRAM size in MB */ #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_SDRAM_BASE0 #define CONFIG_SYS_SDRAM_SIZE CONFIG_SYS_SDRAM_SIZE0 #define CONFIG_SYS_MONITOR_LEN 0x20000 /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization ?? */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ #define CONFIG_FLASH_SHOW_PROGRESS 45 #define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE #define CONFIG_SYS_INT_FLASH_BASE 0xF0000000 #define CONFIG_SYS_INT_FLASH_ENABLE 0x21 #define CONFIG_SYS_FLASH_SIZE 16*1024*1024 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } /*----------------------------------------------------------------------- * Cache Configuration */ #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ CONFIG_SYS_INIT_RAM_SIZE - 8) #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ CONFIG_SYS_INIT_RAM_SIZE - 4) #define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV + CF_CACR_DCM) #define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ CF_ACR_EN | CF_ACR_SM_ALL) #define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_DISD | \ CF_CACR_CEIB | CF_CACR_DBWE | \ CF_CACR_EUSP) /*----------------------------------------------------------------------- * Memory bank definitions */ #define CONFIG_SYS_CS0_BASE 0xFF000000 #define CONFIG_SYS_CS0_CTRL 0x00001980 #define CONFIG_SYS_CS0_MASK 0x00FF0001 #define CONFIG_SYS_CS2_BASE 0xE0000000 #define CONFIG_SYS_CS2_CTRL 0x00001980 #define CONFIG_SYS_CS2_MASK 0x000F0001 #define CONFIG_SYS_CS3_BASE 0xE0100000 #define CONFIG_SYS_CS3_CTRL 0x00001980 #define CONFIG_SYS_CS3_MASK 0x000F0001 /*----------------------------------------------------------------------- * Port configuration */ #define CONFIG_SYS_PACNT 0x0000000 /* Port A D[31:24] */ #define CONFIG_SYS_PADDR 0x0000000 #define CONFIG_SYS_PADAT 0x0000000 #define CONFIG_SYS_PBCNT 0x0000000 /* Port B D[23:16] */ #define CONFIG_SYS_PBDDR 0x0000000 #define CONFIG_SYS_PBDAT 0x0000000 #define CONFIG_SYS_PCCNT 0x0000000 /* Port C D[15:08] */ #define CONFIG_SYS_PCDDR 0x0000000 #define CONFIG_SYS_PCDAT 0x0000000 #define CONFIG_SYS_PDCNT 0x0000000 /* Port D D[07:00] */ #define CONFIG_SYS_PCDDR 0x0000000 #define CONFIG_SYS_PCDAT 0x0000000 #define CONFIG_SYS_PASPAR 0x0F0F #define CONFIG_SYS_PEHLPAR 0xC0 #define CONFIG_SYS_PUAPAR 0x0F #define CONFIG_SYS_DDRUA 0x05 #define CONFIG_SYS_PJPAR 0xFF /*----------------------------------------------------------------------- * I2C */ #ifdef CONFIG_CMD_DATE #define CONFIG_RTC_DS1338 #define CONFIG_I2C_RTC_ADDR 0x68 #endif /*----------------------------------------------------------------------- * VIDEO configuration */ #define CONFIG_SYS_VCXK_DEFAULT_LINEALIGN 2 #define CONFIG_SYS_VCXK_DOUBLEBUFFERED 1 #define CONFIG_SYS_VCXK_BASE CONFIG_SYS_CS2_BASE #define CONFIG_SYS_VCXK_ACKNOWLEDGE_PORT MCFGPTB_GPTPORT #define CONFIG_SYS_VCXK_ACKNOWLEDGE_DDR MCFGPTB_GPTDDR #define CONFIG_SYS_VCXK_ACKNOWLEDGE_PIN 0x0001 #define CONFIG_SYS_VCXK_ENABLE_PORT MCFGPTB_GPTPORT #define CONFIG_SYS_VCXK_ENABLE_DDR MCFGPTB_GPTDDR #define CONFIG_SYS_VCXK_ENABLE_PIN 0x0002 #define CONFIG_SYS_VCXK_REQUEST_PORT MCFGPTB_GPTPORT #define CONFIG_SYS_VCXK_REQUEST_DDR MCFGPTB_GPTDDR #define CONFIG_SYS_VCXK_REQUEST_PIN 0x0004 #define CONFIG_SYS_VCXK_INVERT_PORT MCFGPIO_PORTE #define CONFIG_SYS_VCXK_INVERT_DDR MCFGPIO_DDRE #define CONFIG_SYS_VCXK_INVERT_PIN MCFGPIO_PORT2 #endif /* _CONFIG_M5282EVB_H */ /*---------------------------------------------------------------------*/