# 
# ***** BEGIN LICENSE BLOCK *****
# Version: MPL 1.1/GPL 2.0/LGPL 2.1
#
# The contents of this file are subject to the Mozilla Public License Version
# 1.1 (the "License"); you may not use this file except in compliance with
# the License. You may obtain a copy of the License at
# http://www.mozilla.org/MPL/
#
# Software distributed under the License is distributed on an "AS IS" basis,
# WITHOUT WARRANTY OF ANY KIND, either express or implied. See the License
# for the specific language governing rights and limitations under the
# License.
#
# The Original Code is the Netscape Portable Runtime (NSPR).
#
# The Initial Developer of the Original Code is
# Netscape Communications Corporation.
# Portions created by the Initial Developer are Copyright (C) 1998-2000
# the Initial Developer. All Rights Reserved.
#
# Contributor(s):
#
# Alternatively, the contents of this file may be used under the terms of
# either the GNU General Public License Version 2 or later (the "GPL"), or
# the GNU Lesser General Public License Version 2.1 or later (the "LGPL"),
# in which case the provisions of the GPL or the LGPL are applicable instead
# of those above. If you wish to allow use of your version of this file only
# under the terms of either the GPL or the LGPL, and not to allow others to
# use your version of this file under the terms of the MPL, indicate your
# decision by deleting the provisions above and replace them with the notice
# and other provisions required by the GPL or the LGPL. If you do not delete
# the provisions above, a recipient may use your version of this file under
# the terms of any one of the MPL, the GPL or the LGPL.
#
# ***** END LICENSE BLOCK *****

#
# prerr.properties
# This file is automatically generated; please do not edit it.
PR_OUT_OF_MEMORY_ERROR=Memory allocation attempt failed
PR_BAD_DESCRIPTOR_ERROR=Invalid file descriptor
PR_WOULD_BLOCK_ERROR=The operation would have blocked
PR_ACCESS_FAULT_ERROR=Invalid memory address argument
PR_INVALID_METHOD_ERROR=Invalid function for file type
PR_ILLEGAL_ACCESS_ERROR=Invalid memory address argument
PR_UNKNOWN_ERROR=Some unknown error has occurred
PR_PENDING_INTERRUPT_ERROR=Operation interrupted by another thread
PR_NOT_IMPLEMENTED_ERROR=function not implemented
PR_IO_ERROR=I/O function error
PR_IO_TIMEOUT_ERROR=I/O operation timed out
PR_IO_PENDING_ERROR=I/O operation on busy file descriptor
PR_DIRECTORY_OPEN_ERROR=The directory could not be opened
PR_INVALID_ARGUMENT_ERROR=Invalid function argument
PR_ADDRESS_NOT_AVAILABLE_ERROR=Network address not available (in use?)
PR_ADDRESS_NOT_SUPPORTED_ERROR=Network address type not supported
PR_IS_CONNECTED_ERROR=Already connected
PR_BAD_ADDRESS_ERROR=Network address is invalid
PR_ADDRESS_IN_USE_ERROR=Local Network address is in use
PR_CONNECT_REFUSED_ERROR=Connection refused by peer
PR_NETWORK_UNREACHABLE_ERROR=Network address is presently unreachable
PR_CONNECT_TIMEOUT_ERROR=Connection attempt timed out
PR_NOT_CONNECTED_ERROR=Network file descriptor is not connected
PR_LOAD_LIBRARY_ERROR=Failure to load dynamic library
PR_UNLOAD_LIBRARY_ERROR=Failure to unload dynamic library
PR_FIND_SYMBOL_ERROR=Symbol not found in any of the loaded dynamic libraries
PR_INSUFFICIENT_RESOURCES_ERROR=Insufficient system resources
PR_DIRECTORY_LOOKUP_ERROR=A directory lookup on a network address has failed
PR_TPD_RANGE_ERROR=Attempt to access a TPD key that is out of range
PR_PROC_DESC_TABLE_FULL_ERROR=Process open FD table is full
PR_SYS_DESC_TABLE_FULL_ERROR=System open FD table is full
PR_NOT_SOCKET_ERROR=Network operation attempted on non-network file descriptor
PR_NOT_TCP_SOCKET_ERROR=TCP-specific function attempted on a non-TCP file descriptor
PR_SOCKET_ADDRESS_IS_BOUND_ERROR=TCP file descriptor is already bound
PR_NO_ACCESS_RIGHTS_ERROR=Access Denied
PR_OPERATION_NOT_SUPPORTED_ERROR=The requested operation is not supported by the platform
PR_PROTOCOL_NOT_SUPPORTED_ERROR=The host operating system does not support the protocol requested
PR_REMOTE_FILE_ERROR=Access to the remote file has been severed
PR_BUFFER_OVERFLOW_ERROR=The value requested is too large to be stored in the data buffer provided
PR_CONNECT_RESET_ERROR=TCP connection reset by peer
PR_RANGE_ERROR=Unused
PR_DEADLOCK_ERROR=The operation would have deadlocked
PR_FILE_IS_LOCKED_ERROR=The file is already locked
PR_FILE_TOO_BIG_ERROR=Write would result in file larger than the system allows
PR_NO_DEVICE_SPACE_ERROR=The device for storing the file is full
PR_PIPE_ERROR=Unused
PR_NO_SEEK_DEVICE_ERROR=Unused
PR_IS_DIRECTORY_ERROR=Cannot perform a normal file operation on a directory
PR_LOOP_ERROR=Symbolic link loop
PR_NAME_TOO_LONG_ERROR=File name is too long
PR_FILE_NOT_FOUND_ERROR=File not found
PR_NOT_DIRECTORY_ERROR=Cannot perform directory operation on a normal file
PR_READ_ONLY_FILESYSTEM_ERROR=Cannot write to a read-only file system
PR_DIRECTORY_NOT_EMPTY_ERROR=Cannot delete a directory that is not empty
PR_FILESYSTEM_MOUNTED_ERROR=Cannot delete or rename a file object while the file system is busy
PR_NOT_SAME_DEVICE_ERROR=Cannot rename a file to a file system on another device
PR_DIRECTORY_CORRUPTED_ERROR=The directory object in the file system is corrupted
PR_FILE_EXISTS_ERROR=Cannot create or rename a filename that already exists
PR_MAX_DIRECTORY_ENTRIES_ERROR=Directory is full.  No additional filenames may be added
PR_INVALID_DEVICE_STATE_ERROR=The required device was in an invalid state
PR_DEVICE_IS_LOCKED_ERROR=The device is locked
PR_NO_MORE_FILES_ERROR=No more entries in the directory
PR_END_OF_FILE_ERROR=Encountered end of file
PR_FILE_SEEK_ERROR=Seek error
PR_FILE_IS_BUSY_ERROR=The file is busy
PR_OPERATION_ABORTED_ERROR=The I/O operation was aborted
PR_IN_PROGRESS_ERROR=Operation is still in progress (probably a non-blocking connect)
PR_ALREADY_INITIATED_ERROR=Operation has already been initiated (probably a non-blocking connect)
PR_GROUP_EMPTY_ERROR=The wait group is empty
PR_INVALID_STATE_ERROR=Object state improper for request
PR_NETWORK_DOWN_ERROR=Network is down
PR_SOCKET_SHUTDOWN_ERROR=Socket shutdown
PR_CONNECT_ABORTED_ERROR=Connection aborted
PR_HOST_UNREACHABLE_ERROR=Host is unreachable
PR_LIBRARY_NOT_LOADED_ERROR=The library is not loaded
PR_CALL_ONCE_ERROR=The one-time function was previously called and failed. Its error code is no longer available
PR_MAX_ERROR=Placeholder for the end of the list