The Netwide Disassembler, NDISASM ================================= Introduction ============ The Netwide Disassembler is a small companion program to the Netwide Assembler, NASM. It seemed a shame to have an x86 assembler, complete with a full instruction table, and not make as much use of it as possible, so here's a disassembler which shares the instruction table (and some other bits of code) with NASM. The Netwide Disassembler does nothing except to produce disassemblies of _binary_ source files. NDISASM does not have any understanding of object file formats, like `objdump', and it will not understand DOS .EXE files like `debug' will. It just disassembles. Getting Started: Installation ============================= See `nasm.doc' for installation instructions. NDISASM, like NASM, has a man page which you may want to put somewhere useful, if you are on a Unix system. Running NDISASM =============== To disassemble a file, you will typically use a command of the form ndisasm [-b16 | -b32] filename NDISASM can disassemble 16 bit code or 32 bit code equally easily, provided of course that you remember to specify which it is to work with. If no `-b' switch is present, NDISASM works in 16-bit mode by default. The `-u' switch (for USE32) also invokes 32-bit mode. Two more command line options are `-r' which reports the version number of NDISASM you are running, and `-h' which gives a short summary of command line options. COM Files: Specifying an Origin =============================== To disassemble a DOS .COM file correctly, a disassembler must assume that the first instruction in the file is loaded at address 0x100, rather than at zero. NDISASM, which assumes by default that any file you give it is loaded at zero, will therefore need to be informed of this. The `-o' option allows you to declare a different origin for the file you are disassembling. Its argument may be expressed in any of the NASM numeric formats: decimal by default, if it begins with `$' or `0x' or ends in `H' it's hex, if it ends in `Q' it's octal, and if it ends in `B' it's binary. Hence, to disassemble a .COM file: ndisasm -o100h filename.com will do the trick. Code Following Data: Synchronisation ==================================== Suppose you are disassembling a file which contains some data which isn't machine code, and _then_ contains some machine code. NDISASM will faithfully plough through the data section, producing machine instructions wherever it can (although most of them will look bizarre, and some may have unusual prefixes, e.g. `fs or ax,0x240a'), and generating `db' instructions every so often if it's totally stumped. Then it will reach the code section. Supposing NDISASM has just finished generating a strange machine instruction from part of the data section, and its file position is now one byte _before_ the beginning of the code section. It's entirely possible that another spurious instruction will get generated, starting with the final byte of the data section, and then the correct first instruction in the code section will not be seen because the starting point skipped over it. This isn't really ideal. To avoid this, you can specify a `synchronisation' point, or indeed as many synchronisation points as you like (although NDISASM can only handle 8192 sync points internally). The definition of a sync point is this: NDISASM guarantees to hit sync points exactly during disassembly. If it is thinking about generating an instruction which would cause it to jump over a sync point, it will discard that instruction and output a `db' instead. So it _will_ start disassembly exactly from the sync point, and so you _will_ see all the instructions in your code section. Sync points are specified using the `-s' option: they are measured in terms of the program origin, not the file position. So if you want to synchronise after 32 bytes of a .COM file, you would have to do ndisasm -o100h -s120h file.com rather than ndisasm -o100h -s20h file.com As stated above, you can specify multiple sync markers if you need to, just by repeating the `-s' option. Mixed Code and Data: Automatic (Intelligent) Synchronisation ============================================================ Suppose you are disassembling the boot sector of a DOS floppy (maybe it has a virus, and you need to understand the virus so that you know what kinds of damage it might have done you). Typically, this will contain a JMP instruction, then some data, then the rest of the code. So there is a very good chance of NDISASM being misaligned when the data ends and the code begins. Hence a sync point is needed. On the other hand, why should you have to specify the sync point manually? What you'd do in order to find where the sync point would be, surely, would be to read the JMP instruction, and then to use its target address as a sync point. So can NDISASM do that for you? The answer, of course, is yes: using either of the synonymous switches `-a' (for automatic sync) or `-i' (for intelligent sync) will enable auto-sync mode. Auto-sync mode automatically generates a sync point for any forward-referring PC-relative jump or call instruction that NDISASM encounters. (Since NDISASM is one-pass, if it encounters a PC-relative jump whose target has already been processed, there isn't much it can do about it...) Only PC-relative jumps are processed, since an absolute jump is either through a register (in which case NDISASM doesn't know what the register contains) or involves a segment address (in which case the target code isn't in the same segment that NDISASM is working in, and so the sync point can't be placed anywhere useful). For some kinds of file, this mechanism will automatically put sync points in all the right places, and save you from having to place any sync points manually. However, it should be stressed that auto-sync mode is _not_ guaranteed to catch all the sync points, and you may still have to place some manually. Auto-sync mode doesn't prevent you from declaring manual sync points: it just adds automatically generated ones to the ones you provide. It's perfectly feasible to specify `-i' _and_ some `-s' options. Another caveat with auto-sync mode is that if, by some unpleasant fluke, something in your data section should disassemble to a PC-relative call or jump instruction, NDISASM may obediently place a sync point in a totally random place, for example in the middle of one of the instructions in your code section. So you may end up with a wrong disassembly even if you use auto-sync. Again, there isn't much I can do about this. If you have problems, you'll have to use manual sync points, or use the `-k' option (documented below) to suppress disassembly of the data area. Other Options ============= The `-e' option skips a header on the file, by ignoring the first N bytes. This means that the header is _not_ counted towards the disassembly offset: if you give `-e10 -o10', disassembly will start at byte 10 in the file, and this will be given offset 10, not 20. The `-k' option is provided with two comma-separated numeric arguments, the first of which is an assembly offset and the second is a number of bytes to skip. This _will_ count the skipped bytes towards the assembly offset: its use is to suppress disassembly of a data section which wouldn't contain anything you wanted to see anyway. Bugs and Improvements ===================== There are no known bugs. However, any you find, with patches if possible, should be sent to or , and we'll try to fix them. Feel free to send contributions and new features as well. Future plans include awareness of which processors certain instructions will run on, and marking of instructions that are too advanced for some processor (or are FPU instructions, or are undocumented opcodes, or are privileged protected-mode instructions, or whatever). That's All Folks! ================= I hope NDISASM is of some use to somebody. Including me. :-) I don't recommend taking NDISASM apart to see how an efficient disassembler works, because as far as I know, it isn't an efficient one anyway. You have been warned. Please feel free to send comments, suggestions, or chat to . As with NASM, no flames please. - Simon Tatham , 21-Nov-96