From df66cc24f1796a0f3e73f296a833d4c6b3191e2f Mon Sep 17 00:00:00 2001 From: Tapani Date: Wed, 18 Jul 2012 15:45:56 +0800 Subject: Remove old staging driver for Broadcom bcm4329 wifi (cherry picked from commit 076ad8b1528a6439e9bb629951d8fea6878d1dfc) --- drivers/staging/brcm80211/include/sbsdio.h | 152 ----------------------------- 1 file changed, 152 deletions(-) delete mode 100644 drivers/staging/brcm80211/include/sbsdio.h (limited to 'drivers/staging/brcm80211/include/sbsdio.h') diff --git a/drivers/staging/brcm80211/include/sbsdio.h b/drivers/staging/brcm80211/include/sbsdio.h deleted file mode 100644 index c7facd3795a0..000000000000 --- a/drivers/staging/brcm80211/include/sbsdio.h +++ /dev/null @@ -1,152 +0,0 @@ -/* - * Copyright (c) 2010 Broadcom Corporation - * - * Permission to use, copy, modify, and/or distribute this software for any - * purpose with or without fee is hereby granted, provided that the above - * copyright notice and this permission notice appear in all copies. - * - * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES - * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF - * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY - * SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES - * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION - * OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN - * CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. - */ - -#ifndef _SBSDIO_H -#define _SBSDIO_H - -#define SBSDIO_NUM_FUNCTION 3 /* as of sdiod rev 0, supports 3 functions */ - -/* function 1 miscellaneous registers */ -#define SBSDIO_SPROM_CS 0x10000 /* sprom command and status */ -#define SBSDIO_SPROM_INFO 0x10001 /* sprom info register */ -#define SBSDIO_SPROM_DATA_LOW 0x10002 /* sprom indirect access data byte 0 */ -#define SBSDIO_SPROM_DATA_HIGH 0x10003 /* sprom indirect access data byte 1 */ -#define SBSDIO_SPROM_ADDR_LOW 0x10004 /* sprom indirect access addr byte 0 */ -#define SBSDIO_SPROM_ADDR_HIGH 0x10005 /* sprom indirect access addr byte 0 */ -#define SBSDIO_CHIP_CTRL_DATA 0x10006 /* xtal_pu (gpio) output */ -#define SBSDIO_CHIP_CTRL_EN 0x10007 /* xtal_pu (gpio) enable */ -#define SBSDIO_WATERMARK 0x10008 /* rev < 7, watermark for sdio device */ -#define SBSDIO_DEVICE_CTL 0x10009 /* control busy signal generation */ - -/* registers introduced in rev 8, some content (mask/bits) defs in sbsdpcmdev.h */ -#define SBSDIO_FUNC1_SBADDRLOW 0x1000A /* SB Address Window Low (b15) */ -#define SBSDIO_FUNC1_SBADDRMID 0x1000B /* SB Address Window Mid (b23:b16) */ -#define SBSDIO_FUNC1_SBADDRHIGH 0x1000C /* SB Address Window High (b31:b24) */ -#define SBSDIO_FUNC1_FRAMECTRL 0x1000D /* Frame Control (frame term/abort) */ -#define SBSDIO_FUNC1_CHIPCLKCSR 0x1000E /* ChipClockCSR (ALP/HT ctl/status) */ -#define SBSDIO_FUNC1_SDIOPULLUP 0x1000F /* SdioPullUp (on cmd, d0-d2) */ -#define SBSDIO_FUNC1_WFRAMEBCLO 0x10019 /* Write Frame Byte Count Low */ -#define SBSDIO_FUNC1_WFRAMEBCHI 0x1001A /* Write Frame Byte Count High */ -#define SBSDIO_FUNC1_RFRAMEBCLO 0x1001B /* Read Frame Byte Count Low */ -#define SBSDIO_FUNC1_RFRAMEBCHI 0x1001C /* Read Frame Byte Count High */ - -#define SBSDIO_FUNC1_MISC_REG_START 0x10000 /* f1 misc register start */ -#define SBSDIO_FUNC1_MISC_REG_LIMIT 0x1001C /* f1 misc register end */ - -/* SBSDIO_SPROM_CS */ -#define SBSDIO_SPROM_IDLE 0 -#define SBSDIO_SPROM_WRITE 1 -#define SBSDIO_SPROM_READ 2 -#define SBSDIO_SPROM_WEN 4 -#define SBSDIO_SPROM_WDS 7 -#define SBSDIO_SPROM_DONE 8 - -/* SBSDIO_SPROM_INFO */ -#define SROM_SZ_MASK 0x03 /* SROM size, 1: 4k, 2: 16k */ -#define SROM_BLANK 0x04 /* depreciated in corerev 6 */ -#define SROM_OTP 0x80 /* OTP present */ - -/* SBSDIO_CHIP_CTRL */ -#define SBSDIO_CHIP_CTRL_XTAL 0x01 /* or'd with onchip xtal_pu, - * 1: power on oscillator - * (for 4318 only) - */ -/* SBSDIO_WATERMARK */ -#define SBSDIO_WATERMARK_MASK 0x7f /* number of words - 1 for sd device - * to wait before sending data to host - */ - -/* SBSDIO_DEVICE_CTL */ -#define SBSDIO_DEVCTL_SETBUSY 0x01 /* 1: device will assert busy signal when - * receiving CMD53 - */ -#define SBSDIO_DEVCTL_SPI_INTR_SYNC 0x02 /* 1: assertion of sdio interrupt is - * synchronous to the sdio clock - */ -#define SBSDIO_DEVCTL_CA_INT_ONLY 0x04 /* 1: mask all interrupts to host - * except the chipActive (rev 8) - */ -#define SBSDIO_DEVCTL_PADS_ISO 0x08 /* 1: isolate internal sdio signals, put - * external pads in tri-state; requires - * sdio bus power cycle to clear (rev 9) - */ -#define SBSDIO_DEVCTL_SB_RST_CTL 0x30 /* Force SD->SB reset mapping (rev 11) */ -#define SBSDIO_DEVCTL_RST_CORECTL 0x00 /* Determined by CoreControl bit */ -#define SBSDIO_DEVCTL_RST_BPRESET 0x10 /* Force backplane reset */ -#define SBSDIO_DEVCTL_RST_NOBPRESET 0x20 /* Force no backplane reset */ - -/* SBSDIO_FUNC1_CHIPCLKCSR */ -#define SBSDIO_FORCE_ALP 0x01 /* Force ALP request to backplane */ -#define SBSDIO_FORCE_HT 0x02 /* Force HT request to backplane */ -#define SBSDIO_FORCE_ILP 0x04 /* Force ILP request to backplane */ -#define SBSDIO_ALP_AVAIL_REQ 0x08 /* Make ALP ready (power up xtal) */ -#define SBSDIO_HT_AVAIL_REQ 0x10 /* Make HT ready (power up PLL) */ -#define SBSDIO_FORCE_HW_CLKREQ_OFF 0x20 /* Squelch clock requests from HW */ -#define SBSDIO_ALP_AVAIL 0x40 /* Status: ALP is ready */ -#define SBSDIO_HT_AVAIL 0x80 /* Status: HT is ready */ -/* In rev8, actual avail bits followed original docs */ -#define SBSDIO_Rev8_HT_AVAIL 0x40 -#define SBSDIO_Rev8_ALP_AVAIL 0x80 - -#define SBSDIO_AVBITS (SBSDIO_HT_AVAIL | SBSDIO_ALP_AVAIL) -#define SBSDIO_ALPAV(regval) ((regval) & SBSDIO_AVBITS) -#define SBSDIO_HTAV(regval) (((regval) & SBSDIO_AVBITS) == SBSDIO_AVBITS) -#define SBSDIO_ALPONLY(regval) (SBSDIO_ALPAV(regval) && !SBSDIO_HTAV(regval)) -#define SBSDIO_CLKAV(regval, alponly) (SBSDIO_ALPAV(regval) && \ - (alponly ? 1 : SBSDIO_HTAV(regval))) - -/* SBSDIO_FUNC1_SDIOPULLUP */ -#define SBSDIO_PULLUP_D0 0x01 /* Enable D0/MISO pullup */ -#define SBSDIO_PULLUP_D1 0x02 /* Enable D1/INT# pullup */ -#define SBSDIO_PULLUP_D2 0x04 /* Enable D2 pullup */ -#define SBSDIO_PULLUP_CMD 0x08 /* Enable CMD/MOSI pullup */ -#define SBSDIO_PULLUP_ALL 0x0f /* All valid bits */ - -/* function 1 OCP space */ -#define SBSDIO_SB_OFT_ADDR_MASK 0x07FFF /* sb offset addr is <= 15 bits, 32k */ -#define SBSDIO_SB_OFT_ADDR_LIMIT 0x08000 -#define SBSDIO_SB_ACCESS_2_4B_FLAG 0x08000 /* with b15, maps to 32-bit SB access */ - -/* some duplication with sbsdpcmdev.h here */ -/* valid bits in SBSDIO_FUNC1_SBADDRxxx regs */ -#define SBSDIO_SBADDRLOW_MASK 0x80 /* Valid bits in SBADDRLOW */ -#define SBSDIO_SBADDRMID_MASK 0xff /* Valid bits in SBADDRMID */ -#define SBSDIO_SBADDRHIGH_MASK 0xffU /* Valid bits in SBADDRHIGH */ -#define SBSDIO_SBWINDOW_MASK 0xffff8000 /* Address bits from SBADDR regs */ - -/* direct(mapped) cis space */ -#define SBSDIO_CIS_BASE_COMMON 0x1000 /* MAPPED common CIS address */ -#define SBSDIO_CIS_SIZE_LIMIT 0x200 /* maximum bytes in one CIS */ -#define SBSDIO_OTP_CIS_SIZE_LIMIT 0x078 /* maximum bytes OTP CIS */ - -#define SBSDIO_CIS_OFT_ADDR_MASK 0x1FFFF /* cis offset addr is < 17 bits */ - -#define SBSDIO_CIS_MANFID_TUPLE_LEN 6 /* manfid tuple length, include tuple, - * link bytes - */ - -/* indirect cis access (in sprom) */ -#define SBSDIO_SPROM_CIS_OFFSET 0x8 /* 8 control bytes first, CIS starts from - * 8th byte - */ - -#define SBSDIO_BYTEMODE_DATALEN_MAX 64 /* sdio byte mode: maximum length of one - * data command - */ - -#define SBSDIO_CORE_ADDR_MASK 0x1FFFF /* sdio core function one address mask */ - -#endif /* _SBSDIO_H */ -- cgit v1.2.1