# Copyright 2022 The ChromiumOS Authors
# Use of this source code is governed by a BSD-style license that can be
# found in the LICENSE file.

if PLATFORM_EC_USBC

menuconfig PLATFORM_EC_USB_MUX
	bool "USB muxes"
	default y
	depends on DT_HAS_CROS_EC_USB_MUX_CHAIN_ENABLED
	help
	  Enables support for USB muxes. These allow multiplexing

if PLATFORM_EC_USB_MUX

config PLATFORM_EC_USB_MUX_TASK
	bool "Run mux set operations in a dedicated thread"
	default n
	help
	  Run a dedicated task to process USB mux sets and HPD, which avoids
	  blocking the PD task on mux updates. This is useful if a mux is slow
	  to update, since blocking PD handling during mux operations can cause
	  timing violations.

config TASK_USB_MUX_STACK_SIZE
	int "USB mux task stack size"
	depends on PLATFORM_EC_USB_MUX_TASK
	default 1024
	help
	  Set the size of the USB mux task stack, in bytes.

config PLATFORM_EC_USB_MUX_AP_CONTROL
	bool "AP USB mux control"
	depends on PLATFORM_EC_USB_MUX_TASK
	help
	  Allows the AP to send commands in order to control any muxes and
	  retimers for the board.

config PLATFORM_EC_USB_MUX_AMD_FP6
	bool "AMD FP6 integrated mux"
	default y
	depends on DT_HAS_AMD_USBC_MUX_AMD_FP6_ENABLED
	help
	  Integrated AMD FP6 mux for USB and DP.  Mux control happens over
	  an i2c channel.

config PLATFORM_EC_USB_MUX_IT5205
	bool "ITE IT5205 USB Type-C 3:2 Alternative mode passive mux"
	default y
	depends on DT_HAS_ITE_IT5205_ENABLED
	help
	  This is a USB Type-C 3:2 Alternative mode mux, supporting USB 3.1
	  Gen 2 10Gbps as well as DisplayPort (DP1.4) at 8Gbps. It provides a
	  cross-point mux for low-speed Side-Band-Use (SBU) pins. The mux can
	  be controlled via I2C.

config PLATFORM_EC_USB_MUX_PS8743
	bool "Parade PS8743 USB-C Host Switch with redriver"
	default y
	depends on DT_HAS_PARADE_PS8743_ENABLED || DT_HAS_ZEPHYR_PS8743_EMUL_ENABLED
	help
	  This is a Parade USB 3.1 Gen 1 / DisplayPort (DP) Alt Mode
	  High-Bit-Rate 2 (HBR2) redriver. It provides control of switching
	  modes through either GPIO or I2C.

choice PLATFORM_EC_USB_MUX_TUSB_TYPE
	prompt "Select the TUSB USB-C Redriver type"
	optional
	help
	  There are three supported types of TUSB USB-C Redriver: TUSB546,
	  TUSB1044, and TUSB1064.

config PLATFORM_EC_USB_MUX_TUSB546
	bool "TI TUSB546 USB-C DP ALT Mode Linear Redriver Crosspoint Switch"
	help
	  This is a USB Type-C Alt Mode redriving switch supporting USB 3.1 data
	  rates up to 5 Gbps and DisplayPort 1.4 up to 8.1 Gbps for downstream
	  facing port.

config PLATFORM_EC_USB_MUX_TUSB1044
	bool "TI TUSB1044 USB-C 10 Gbps Linear Redriver"
	help
	  This is a USB Type-C Alt Mode redriver. This supports USB 3.1
	  Gen 2 and DisplayPort 1.4 as Alternate Mode. It Provides GPIO and
	  I2C Control for Channel Direction and Equalization.

config PLATFORM_EC_USB_MUX_TUSB1064
	bool "TI TUSB1064 USB-C 10 Gbps Linear Redriver"
	help
	  This is a USB Type-C Alt Mode redriver. This supports USB 3.1
	  Gen 2 and DisplayPort 1.4.

endchoice # PLATFORM_EC_USB_MUX_TUSB_TYPE

endif # PLATFORM_EC_USB_MUX

endif # PLATFORM_EC_USBC