/* Copyright 2016 The Chromium OS Authors. All rights reserved. * Use of this source code is governed by a BSD-style license that can be * found in the LICENSE file. */ /* * config.h - Top-level configuration Chrome EC * * All configuration settings (CONFIG_*) are defined in this file or in a * sub-configuration file (config_chip.h, board.h, etc.) included by this file. * * Note that this file is included by assembly (.S) files. Any C-isms such as * struct definitions or enums in a sub-configuration file MUST be guarded with * #ifndef __ASSEMBLER__ to prevent those C-isms from being evaluated by the * assembler. */ #ifndef __CROS_EC_CONFIG_H #define __CROS_EC_CONFIG_H /* * All config options are listed alphabetically and described here. * * If you add a new config option somewhere in the code, you must add a * default value here and describe what it does. * * To get a list current list, run this command: * git grep " CONFIG_" | grep -o "CONFIG_[A-Za-z0-9_]\+" | sort | uniq * * Some options are #defined here to enable them by default. Chips or boards * may override this by #undef'ing them in config_chip.h or board.h, * respectively. * * TODO(crosbug.com/p/23758): Describe all of these. Also describe the * HAS_TASK_* macro and how/when it should be used vs. a config define. And * BOARD_*, CHIP_*, and CHIP_FAMILY_*. */ /* * Add support for sensor FIFO: * define the size of the global fifo, must be a power of 2. */ #undef CONFIG_ACCEL_FIFO /* The amount of free entries that trigger an interrupt to the AP. */ #undef CONFIG_ACCEL_FIFO_THRES /* * Sensors in this mask are in forced mode: they needed to be polled * at their data rate frequency. */ #undef CONFIG_ACCEL_FORCE_MODE_MASK /* Enable accelerometer interrupts. */ #undef CONFIG_ACCEL_INTERRUPTS /* * Support "spoof" mode for sensors. This allows sensors to have their values * spoofed to any arbitrary value. This is useful for testing. */ #define CONFIG_ACCEL_SPOOF_MODE /* Specify type of accelerometers attached. */ #undef CONFIG_ACCEL_BMA255 #undef CONFIG_ACCEL_KXCJ9 #undef CONFIG_ACCEL_KX022 #undef CONFIG_ACCEL_LIS2DH #undef CONFIG_ACCELGYRO_LSM6DS0 #undef CONFIG_ACCELGYRO_BMI160 #undef CONFIG_ACCELGYRO_LSM6DSM /* Support for BMI160 hardware orientation sensor */ #undef CONFIG_BMI160_ORIENTATION_SENSOR /* Support for KIONIX KX022 hardware orientation sensor */ #undef CONFIG_KX022_ORIENTATION_SENSOR /* * Define if either CONFIG_BMI160_ORIENTATION_SUPPORT or * CONFIG_KX022_ORIENTATION_SUPPORT is set. */ #undef CONFIG_ORIENTATION_SENSOR /* Support the orientation gesture */ #undef CONFIG_GESTURE_ORIENTATION /* Specify barometer attached */ #undef CONFIG_BARO_BMP280 /* * Use the old standard reference frame for accelerometers. The old * reference frame is: * Z-axis: perpendicular to keyboard, pointing up, such that if the device * is sitting flat on a table, the accel reads +G. * X-axis: in the plane of the keyboard, pointing from the front lip to the * hinge, such that if the device is oriented with the front lip touching * the table and the hinge directly above, the accel reads +G. * Y-axis: in the plane of the keyboard, pointing to the right, such that * if the device is on it's left side, the accel reads +G. * * Also, in the old reference frame, the lid accel matches the base accel * readings when lid is closed. */ #undef CONFIG_ACCEL_STD_REF_FRAME_OLD /* Set when INT2 is an ouptut */ #undef CONFIG_ACCELGYRO_BMI160_INT2_OUTPUT /* Specify type of Gyrometers attached. */ #undef CONFIG_GYRO_L3GD20H /* Sync event driver */ #undef CONFIG_SYNC /* Simulate command for sync */ #undef CONFIG_SYNC_COMMAND /* * Define the event to raise when the sync event happens. * Must be within TASK_EVENT_MOTION_INTERRUPT_MASK. */ #undef CONFIG_SYNC_INT_EVENT /* Compile chip support for analog-to-digital convertor */ #undef CONFIG_ADC /* * ADC sample time selection. The value is chip-dependent. * TODO: Replace this with CONFIG_ADC_PROFILE entries. */ #undef CONFIG_ADC_SAMPLE_TIME /* Include the ADC analog watchdog feature in the ADC code */ #define CONFIG_ADC_WATCHDOG /* * Chip-dependent ADC configuration - select one. * SINGLE - Sample all inputs once when requested. * FAST_CONTINUOUS - Sample all inputs continuously using DMA, with minimal * sample time. */ #define CONFIG_ADC_PROFILE_SINGLE #undef CONFIG_ADC_PROFILE_FAST_CONTINUOUS /* * Some ALS modules may be connected to the EC. We need the command, and * specific drivers for each module. */ #ifdef HAS_TASK_ALS #define CONFIG_ALS #else #undef CONFIG_ALS #endif #undef CONFIG_ALS_AL3010 #undef CONFIG_ALS_BH1730 /* * If defined, BH1730 uses board specific lux calculation formula parameters. * If not defined, BH1730 uses default parameters to calculate lux. */ #undef CONFIG_ALS_BH1730_LUXTH_PARAMS #undef CONFIG_ALS_ISL29035 #undef CONFIG_ALS_OPT3001 /* Define the exact model ID present on the board: SI1141 = 41, SI1142 = 42, */ #undef CONFIG_ALS_SI114X /* Check if the device revision is supported */ #undef CONFIG_ALS_SI114X_CHECK_REVISION /* * Define the event to raise when a sensor interrupt triggers. * Must be within TASK_EVENT_MOTION_INTERRUPT_MASK. */ #undef CONFIG_ACCELGYRO_BMI160_INT_EVENT #undef CONFIG_ACCEL_LSM6DSM_INT_EVENT #undef CONFIG_ACCEL_LIS2DH_INT_EVENT #undef CONFIG_ALS_SI114X_INT_EVENT /* * Enable Si114x to operate in polling mode. This config is used in conjunction * with CONFIG_ALS_SI114X_INT_EVENT. When polling is enabled, the read is * initiated in the same manner as when interrupts are used, but the event which * triggers the irq_handler is generated by deferred call using a fixed delay. */ #undef CONFIG_ALS_SI114X_POLLING /* Define which ALS sensor is used for dimming the lightbar when dark */ #undef CONFIG_ALS_LIGHTBAR_DIMMING /* Support AP hang detection host command and state machine */ #undef CONFIG_AP_HANG_DETECT /* Support AP Warm reset Interrupt. */ #undef CONFIG_AP_WARM_RESET_INTERRUPT /* * Enable support for CPU caches behaving according to the ARMv7-M ISA. * (so far, only the Cortex-M7 has such caches) */ #undef CONFIG_ARMV7M_CACHE /* * Defined if core/ code provides assembly optimized implementation of * multiply-accumulate operations (32-bit operands, 64-bit result), for the * cores that lack native instructions. */ #undef CONFIG_ASSEMBLY_MULA32 /* Allow proprietary communication protocols' extensions. */ #undef CONFIG_EXTENSION_COMMAND /* * Support controlling the display backlight based on the state of the lid * switch. The EC will disable the backlight when the lid is closed. * * The GPIO should be named GPIO_BACKLIGHT_ENABLED if active high, or * GPIO_BACKLIGHT_ENABLED_L if active low. See CONFIG_BACKLIGHT_LID_ACTIVE_LOW. */ #undef CONFIG_BACKLIGHT_LID /* * The backlight GPIO pin is active low and named GPIO_BACKLIGHT_ENABLED_L */ #undef CONFIG_BACKLIGHT_LID_ACTIVE_LOW /* * If defined, EC will enable the backlight signal only if this GPIO is * asserted AND the lid is open. This supports passing the backlight-enable * signal from the AP through EC. */ #undef CONFIG_BACKLIGHT_REQ_GPIO /* Support base32 text encoding */ #undef CONFIG_BASE32 /*****************************************************************************/ /* Battery config */ /* Support a simple battery. */ #undef CONFIG_BATTERY /* * Compile battery-specific code. * * Note that some boards have their own unique battery constants / functions. * In this case, those are provided in board/(boardname)/battery.c, and none of * these are defined. * Defining one of these will automatically define CONFIG_BATTERY near the end * of this file. If you add a new config here, you'll need to update that * check. */ #undef CONFIG_BATTERY_BQ20Z453 #undef CONFIG_BATTERY_BQ27541 #undef CONFIG_BATTERY_BQ27621 #undef CONFIG_BATTERY_MAX17055 /* Compile mock battery support; used by tests. */ #undef CONFIG_BATTERY_MOCK /* Maximum time to wake a non-responsive battery, in second */ #define CONFIG_BATTERY_PRECHARGE_TIMEOUT 30 /* * If defined, the charger will check a board specific function for battery hw * presence as an additional condition to determine if power on is allowed for * factory override, where allowing booting of a bare board with no battery and * no power button press is required. */ #undef CONFIG_BATTERY_HW_PRESENT_CUSTOM /* * If defined, the charger will check for battery presence before attempting * to communicate with it. This avoids the 30 second delay when booting * without a battery present. Do not use with CONFIG_BATTERY_PRESENT_GPIO. * * Replace the default battery_is_present() function with a board-specific * implementation in board.c */ #undef CONFIG_BATTERY_PRESENT_CUSTOM /* * If defined, GPIO which is driven low when battery is present. * Charger will check for battery presence before attempting to communicate * with it. This avoids the 30 second delay when booting without a battery * present. Do not use with CONFIG_BATTERY_PRESENT_CUSTOM. */ #undef CONFIG_BATTERY_PRESENT_GPIO /* * Compile smart battery support * * For batteries which support this specification: * http://sbs-forum.org/specs/sbdat110.pdf) */ #undef CONFIG_BATTERY_SMART /* Chemistry of the battery device */ #undef CONFIG_BATTERY_DEVICE_CHEMISTRY /* * Critical battery shutdown timeout (seconds) * * If the battery is at extremely low charge (and discharging) or extremely * high temperature, the EC will shut itself down. This defines the timeout * period in seconds between the critical condition being detected and the * EC shutting itself down. Note that if the critical condition is corrected * before the timeout expiration, the EC will not shut itself down. * */ #define CONFIG_BATTERY_CRITICAL_SHUTDOWN_TIMEOUT 30 /* Perform a battery cut-off when we reach the battery critical level */ #undef CONFIG_BATTERY_CRITICAL_SHUTDOWN_CUT_OFF /* * Support battery cut-off as host command and console command. * * Once defined, you have to implement a board_cut_off_battery() function * in board/???/battery.c file. */ #undef CONFIG_BATTERY_CUT_OFF /* * The default delay is 1 second. Define this if a board prefers * different delay. */ #undef CONFIG_BATTERY_CUTOFF_DELAY_US /* * The board-specific battery.c implements get and set functions to read and * write arbirary vendor-specific parameters stored in the battery. * See include/battery.h for prototypes. */ #undef CONFIG_BATTERY_VENDOR_PARAM /* * TODO(crosbug.com/p/29467): allows charging of a dead battery that * requests nil for current and voltage. Remove this workaround when * possible. */ #undef CONFIG_BATTERY_REQUESTS_NIL_WHEN_DEAD /* * Check for battery in disconnect state (similar to cut-off state). If this * battery is found to be in disconnect state, take it out of this state by * force-applying a charge current. */ #undef CONFIG_BATTERY_REVIVE_DISCONNECT /* * Specify the battery percentage at which the host is told it is full. * If this value is not specified the default is 97% set in battery.h. */ #undef CONFIG_BATTERY_LEVEL_NEAR_FULL /* * Use an alternative method to store battery information: Instead of writing * directly to host memory mapped region, this keeps the battery information in * ec_response_battery_static/dynamic_info structures, that can then be fetched * using host commands, or via EC_ACPI_MEM_BATTERY_INDEX command, which tells * the EC to update the shared memory. * * This is required on dual-battery systems, and on on hostless bases with a * battery. */ #undef CONFIG_BATTERY_V2 /* * Number of batteries, only matters when CONFIG_BATTERY_V2 is used. */ #undef CONFIG_BATTERY_COUNT /* * Expose some data when it is needed. * For example, battery disconnect state */ #undef CONFIG_CHARGE_STATE_DEBUG /* Include support for Bluetooth LE */ #undef CONFIG_BLUETOOTH_LE /* Include support for testing the radio for Bluetooth LE */ #undef CONFIG_BLUETOOTH_LE_RADIO_TEST /* Include support for the HCI and link layers for Bluetooth LE */ #undef CONFIG_BLUETOOTH_LE_STACK /* Include debugging support for the Bluetooth link layer */ #undef CONFIG_BLUETOOTH_LL_DEBUG /* Include debugging support for Bluetooth HCI */ #undef CONFIG_BLUETOOTH_HCI_DEBUG /* Boot header storage offset. */ #undef CONFIG_BOOT_HEADER_STORAGE_OFF /* Size of boot header in storage. */ #undef CONFIG_BOOT_HEADER_STORAGE_SIZE /*****************************************************************************/ /* EC has GPIOs to allow board to reset RTC */ #undef CONFIG_BOARD_HAS_RTC_RESET /* * Call board_before_rsmrst(state) before passing RSMRST# to the AP. * This is for board workarounds that are required after rails are up * but before the AP is out of reset. */ #undef CONFIG_BOARD_HAS_BEFORE_RSMRST /* * Call board_config_post_gpio_init() after GPIOs are initialized. See * include/board_config.h for more information. */ #undef CONFIG_BOARD_POST_GPIO_INIT /* * Call board_config_pre_init() before any inits are called. See * include/board_config.h for more information. */ #undef CONFIG_BOARD_PRE_INIT /* EC has GPIOs attached to board version stuffing resistors */ #undef CONFIG_BOARD_VERSION /* The decoding of the GPIOs defining board version is defined in board code */ #undef CONFIG_BOARD_SPECIFIC_VERSION /* EC responses to a board defined I2C slave address */ #undef CONFIG_BOARD_I2C_SLAVE_ADDR /* * The board is unable to distinguish EC reset from power-on so it should treat * all resets as triggered by RESET_PIN even if it is a POWER_ON reset. */ #undef CONFIG_BOARD_FORCE_RESET_PIN /* Permanent LM4 boot configuration */ #undef CONFIG_BOOTCFG_VALUE /*****************************************************************************/ /* Modify the default behavior to make system bringup easier. */ #undef CONFIG_BRINGUP /* * Enable debug prints / asserts that may helpful for debugging board bring-up, * but probably shouldn't be enabled for production for performance reasons. */ #undef CONFIG_DEBUG_BRINGUP /*****************************************************************************/ /* * Support for entering recovery mode using the volume buttons or a dedicated * recovery button. Note that these are *buttons* and not keys in the keyboard * matrix. */ #undef CONFIG_BUTTON_TRIGGERED_RECOVERY /* * Indicates there is a dedicated recovery button. Note, that if there are * volume buttons, a dedicated recovery button is not needed. This is intended * because if a board has volume buttons, they can do everything a dedicated * recovery button can do. */ #undef CONFIG_DEDICATED_RECOVERY_BUTTON /* * The board has volume up and volume down buttons. Note, these are *buttons* * and not keys in the keyboard matrix. */ #undef CONFIG_VOLUME_BUTTONS /* Support V1 CCD configuration */ #undef CONFIG_CASE_CLOSED_DEBUG_V1 /* Allow unsafe debugging functionality in V1 configuration */ #undef CONFIG_CASE_CLOSED_DEBUG_V1_UNSAFE /* * Capsense chip has buttons, too. */ #undef CONFIG_CAPSENSE /*****************************************************************************/ /* Compile charge manager */ #undef CONFIG_CHARGE_MANAGER /* Number of charge ports excluding type-c ports */ #define CONFIG_DEDICATED_CHARGE_PORT_COUNT 0 /* Allow charge manager to default to charging from dual-role partners */ #undef CONFIG_CHARGE_MANAGER_DRP_CHARGING /* Handle the external power limit host command in charge manager */ #undef CONFIG_CHARGE_MANAGER_EXTERNAL_POWER_LIMIT /* Initially enter safe mode, with relaxed port / current selection rules */ #define CONFIG_CHARGE_MANAGER_SAFE_MODE /* Leave safe mode when battery pct meets or exceeds this value */ #define CONFIG_CHARGE_MANAGER_BAT_PCT_SAFE_MODE_EXIT 2 /* The hardware has some input current ramping/back-off mechanism */ #undef CONFIG_CHARGE_RAMP_HW /* Compile input current ramping support using software control */ #undef CONFIG_CHARGE_RAMP_SW /*****************************************************************************/ /* Charger config */ /* Compile common charge state code. You must pick an implementation. */ #undef CONFIG_CHARGER #undef CONFIG_CHARGER_V2 /* Compile charger-specific code for these chargers (pick at most one) */ #undef CONFIG_CHARGER_BD9995X #undef CONFIG_CHARGER_BQ24707A #undef CONFIG_CHARGER_BQ24715 #undef CONFIG_CHARGER_BQ24725 #undef CONFIG_CHARGER_BQ24735 #undef CONFIG_CHARGER_BQ24738 #undef CONFIG_CHARGER_BQ24770 #undef CONFIG_CHARGER_BQ24773 #undef CONFIG_CHARGER_BQ25890 #undef CONFIG_CHARGER_BQ25892 #undef CONFIG_CHARGER_BQ25895 #undef CONFIG_CHARGER_ISL9237 #undef CONFIG_CHARGER_ISL9238 #undef CONFIG_CHARGER_RT9466 #undef CONFIG_CHARGER_RT9467 #undef CONFIG_CHARGER_SY21612 /* * Enable the CHG_EN at initialization to turn-on the BGATE which allows voltage * to be applied to the battery PACK & wakes the battery if it is in shipmode. */ #undef CONFIG_CHARGER_BD9995X_CHGEN /* * BD9995X Power Save Mode * * Which power save mode should the charger enter when VBUS is removed. Check * driver/bd9995x.h for the power save settings. By default, no power save mode * is enabled. */ #undef CONFIG_BD9995X_POWER_SAVE_MODE /* * If the battery temperature sense pin is connected to charger, * get the battery temperature from the charger. */ #undef CONFIG_CHARGER_BATTERY_TSENSE /* * BQ2589x IR Compensation settings. * Should be the combination of BQ2589X_IR_TREG_xxxC, BQ2589X_IR_VCLAMP_yyyMV * and BQ2589X_IR_BAT_COMP_zzzMOHM. */ #undef CONFIG_CHARGER_BQ2589X_IR_COMP /* * BQ2589x 5V boost current limit and voltage. * Should be the combination of BQ2589X_BOOSTV_MV(voltage) and * BQ2589X_BOOST_LIM_xxxMA. */ #undef CONFIG_CHARGER_BQ2589X_BOOST /* * Board specific charging current limit, in mA. If defined, the charge state * machine will not allow the battery to request more current than this. */ #undef CONFIG_CHARGER_CURRENT_LIMIT /* * Enable/disable system power monitor PSYS function: this enables output * from charger chip to SoC. */ #undef CONFIG_CHARGER_PSYS /* * Enable reading PSYS (system power) value, either via "psys" console command, * or via charger_get_system_power function. */ #undef CONFIG_CHARGER_PSYS_READ /* * Board specific charging current termination limit, in mA. If defined and * charger supports setting termination current it should be set during charger * init. * * TODO(tbroch): Only valid for bq2589x currently. Configure defaults for other * charger ICs that support termination currents. */ #undef CONFIG_CHARGER_TERM_CURRENT_LIMIT /* * Board supports discharge mode. In this mode, the battery will discharge * even if AC is present. Used for testing. */ #undef CONFIG_CHARGER_DISCHARGE_ON_AC /* Board has a custom discharge mode. */ #undef CONFIG_CHARGER_DISCHARGE_ON_AC_CUSTOM /* * Board specific flag used to disable external ILIM pin used to determine input * current limit. When defined, the input current limit is decided only by * the software register value. */ #undef CONFIG_CHARGER_ILIM_PIN_DISABLED /* * Default input current for the board, in mA. * * This value should depend on external power adapter, designed charging * voltage, and the maximum power of the running system. For type-C chargers, * this should be set to 512 mA in order to not brown-out low-current USB * charge ports. */ #undef CONFIG_CHARGER_INPUT_CURRENT /* * Board specific maximum input current limit, in mA. */ #undef CONFIG_CHARGER_MAX_INPUT_CURRENT /* * Leave charger VBAT configured to battery-requested voltage under all * conditions, even when AC is not present. This may be necessary to work * around quirks of certain charger chips, such as the BD9995X. */ #undef CONFIG_CHARGER_MAINTAIN_VBAT /* Minimum battery percentage for power on */ #undef CONFIG_CHARGER_MIN_BAT_PCT_FOR_POWER_ON /* Set this option when using a Narrow VDC (NVDC) charger, such as ISL9237/8. */ #undef CONFIG_CHARGER_NARROW_VDC /* * Low energy thresholds - when battery level is below BAT_PCT and an external * charger provides less than CHG_MW of power, inform the AP of the situation * through the LIMIT_POWER host event. */ #undef CONFIG_CHARGER_LIMIT_POWER_THRESH_BAT_PCT #undef CONFIG_CHARGER_LIMIT_POWER_THRESH_CHG_MW /* * Enable charger's OTG functions, i.e. make it possible to supply output power * from battery. */ #undef CONFIG_CHARGER_OTG /* * Charger should call battery_override_params() to limit/correct the voltage * and current requested by the battery pack before acting on the request. * * This is valid with CONFIG_CHARGER_V2 only. */ #undef CONFIG_CHARGER_PROFILE_OVERRIDE /* * Common code for charger profile override. Should be used with * CONFIG_CHARGER_PROFILE_OVERRIDE. */ #undef CONFIG_CHARGER_PROFILE_OVERRIDE_COMMON /* * Battery voltage threshold ranges for charge profile override. * Override it in board.h if battery has multiple threshold ranges. */ #define CONFIG_CHARGER_PROFILE_VOLTAGE_RANGES 2 /* Value of the charge sense resistor, in mOhms */ #undef CONFIG_CHARGER_SENSE_RESISTOR /* Value of the input current sense resistor, in mOhms */ #undef CONFIG_CHARGER_SENSE_RESISTOR_AC /* * Board has an GPIO pin to enable or disable charging. * * This GPIO should be named GPIO_CHARGER_EN, if active high. Or * GPIO_CHARGER_EN_L if active low. */ #undef CONFIG_CHARGER_EN_GPIO /* Charger enable GPIO is active low */ #undef CONFIG_CHARGER_EN_ACTIVE_LOW /* Enable trickle charging */ #undef CONFIG_TRICKLE_CHARGING /*****************************************************************************/ /* * The chip needs to define special SRAM memory regions as linker sections. * Those regions are defined in the special-purpose preprocessed file in * chip//memory_regions.inc using the following macro: * REGION(name, attributes, start_address, size) * * Note: these 'special' regions are NOT cleared at startup contrary to .bss. */ #undef CONFIG_CHIP_MEMORY_REGIONS /* * Chip needs to do pre-init very early in main(), and provides chip_pre_init() * to do so. */ #undef CONFIG_CHIP_PRE_INIT /*****************************************************************************/ /* Chipset config */ /* AP chipset support; pick at most one */ #undef CONFIG_CHIPSET_APOLLOLAKE /* Intel Apollolake (x86) */ #undef CONFIG_CHIPSET_BRASWELL /* Intel Braswell (x86) */ #undef CONFIG_CHIPSET_CANNONLAKE /* Intel Cannonlake (x86) */ #undef CONFIG_CHIPSET_ECDRIVEN /* Dummy power module */ #undef CONFIG_CHIPSET_GEMINILAKE /* Intel Geminilake (x86) */ #undef CONFIG_CHIPSET_MEDIATEK /* MediaTek MT81xx */ #undef CONFIG_CHIPSET_RK3399 /* Rockchip rk3399 */ /* TODO: Rename below config to CONFIG_CHIPSET_RK32XX */ #undef CONFIG_CHIPSET_ROCKCHIP /* Rockchip rk32xx */ #undef CONFIG_CHIPSET_SKYLAKE /* Intel Skylake (x86) */ #undef CONFIG_CHIPSET_STONEY /* AMD Stoney (x86)*/ /* Shared chipset support; automatically gets defined below. */ #undef CONFIG_CHIPSET_APL_GLK /* Apollolake & Geminilake */ /* Support chipset throttling */ #undef CONFIG_CHIPSET_CAN_THROTTLE /* Enable additional chipset debugging */ #undef CONFIG_CHIPSET_DEBUG /* Enable chipset reset hook, requires a deferrable function */ #undef CONFIG_CHIPSET_RESET_HOOK /* Support power rail control */ #define CONFIG_CHIPSET_HAS_PP1350 #define CONFIG_CHIPSET_HAS_PP5000 /* Support PMIC reset(using LDO_EN) in chipset */ #undef CONFIG_CHIPSET_HAS_PLATFORM_PMIC_RESET /* Redefine when we need a different power-on sequence on the same chipset. */ #define CONFIG_CHIPSET_POWER_SEQ_VERSION 0 /*****************************************************************************/ /* * Chip config for clock circuitry * define = crystal / undef = oscillator */ #undef CONFIG_CLOCK_CRYSTAL /* Indicate if a clock source is connected to stm32f4's "HSE" specific input */ #undef CONFIG_STM32_CLOCK_HSE_HZ /* Indicate if a clock source is connected to "LSE" specific input */ #undef CONFIG_STM32_CLOCK_LSE /* * Chip config for clock source * define = external crystal oscillator / undef = internal clock source */ #undef CONFIG_CLOCK_SRC_EXTERNAL /*****************************************************************************/ /* Support curve25519 public key cryptography */ #undef CONFIG_CURVE25519 /*****************************************************************************/ /* PMIC config */ /* Support firmware long press power-off timer */ #undef CONFIG_PMIC_FW_LONG_PRESS_TIMER /* Support PMIC power control */ #undef CONFIG_PMIC /*****************************************************************************/ /* * Optional console commands * * Defining these options will enable the corresponding command on the EC * console. */ #undef CONFIG_CMD_ACCELS #undef CONFIG_CMD_ACCEL_FIFO #undef CONFIG_CMD_ACCEL_INFO #define CONFIG_CMD_ACCELSPOOF #define CONFIG_CMD_ADC #undef CONFIG_CMD_ALS #define CONFIG_CMD_APTHROTTLE #undef CONFIG_CMD_BATDEBUG #define CONFIG_CMD_BATTFAKE #undef CONFIG_CMD_BATT_MFG_ACCESS #undef CONFIG_CMD_BUTTON #undef CONFIG_CMD_CCD_DISABLE /* 'ccd disable' subcommand */ #define CONFIG_CMD_CHARGER #undef CONFIG_CMD_CHARGER_ADC_AMON_BMON #undef CONFIG_CMD_CHARGER_PROFILE_OVERRIDE #undef CONFIG_CMD_CHARGER_PROFILE_OVERRIDE_TEST #define CONFIG_CMD_CHARGE_SUPPLIER_INFO #undef CONFIG_CMD_CHGRAMP #undef CONFIG_CMD_CLOCKGATES #undef CONFIG_CMD_COMXTEST #define CONFIG_CMD_CRASH #define CONFIG_CMD_DEVICE_EVENT #undef CONFIG_CMD_ECTEMP #define CONFIG_CMD_FASTCHARGE #undef CONFIG_CMD_FLASH #define CONFIG_CMD_FLASHINFO #undef CONFIG_CMD_FLASH_TRISTATE #undef CONFIG_CMD_FORCETIME #define CONFIG_CMD_GETTIME #undef CONFIG_CMD_GPIO_EXTENDED #undef CONFIG_CMD_GSV #define CONFIG_CMD_HASH #define CONFIG_CMD_HCDEBUG #undef CONFIG_CMD_HOSTCMD #undef CONFIG_CMD_I2CWEDGE #undef CONFIG_CMD_I2C_PROTECT #define CONFIG_CMD_I2C_SCAN #undef CONFIG_CMD_I2C_STRESS_TEST #undef CONFIG_CMD_I2C_STRESS_TEST_ACCEL #undef CONFIG_CMD_I2C_STRESS_TEST_ALS #undef CONFIG_CMD_I2C_STRESS_TEST_BATTERY #undef CONFIG_CMD_I2C_STRESS_TEST_CHARGER #undef CONFIG_CMD_I2C_STRESS_TEST_TCPC #define CONFIG_CMD_I2C_XFER #define CONFIG_CMD_IDLE_STATS #undef CONFIG_CMD_ILIM #define CONFIG_CMD_INA #undef CONFIG_CMD_JUMPTAGS #define CONFIG_CMD_KEYBOARD #undef CONFIG_CMD_LEDTEST #undef CONFIG_CMD_LID_ANGLE #undef CONFIG_CMD_MCDP #define CONFIG_CMD_MD #define CONFIG_CMD_MEM #define CONFIG_CMD_MMAPINFO #define CONFIG_CMD_PD #undef CONFIG_CMD_PD_CONTROL #undef CONFIG_CMD_PD_DEV_DUMP_INFO #undef CONFIG_CMD_PD_FLASH #undef CONFIG_CMD_PLL #undef CONFIG_CMD_PMU #define CONFIG_CMD_POWERINDEBUG #undef CONFIG_CMD_POWERLED #define CONFIG_CMD_PWR_AVG #define CONFIG_CMD_POWER_AP #undef CONFIG_CMD_PPC_DUMP #define CONFIG_CMD_REGULATOR #undef CONFIG_CMD_RTC #undef CONFIG_CMD_RTC_ALARM #define CONFIG_CMD_RW #undef CONFIG_CMD_SCRATCHPAD #define CONFIG_CMD_SHMEM #undef CONFIG_CMD_SLEEP #define CONFIG_CMD_SLEEPMASK #undef CONFIG_CMD_SPI_FLASH #undef CONFIG_CMD_SPI_NOR #undef CONFIG_CMD_SPI_XFER #undef CONFIG_CMD_STACKOVERFLOW #define CONFIG_CMD_SYSINFO #define CONFIG_CMD_SYSJUMP #define CONFIG_CMD_SYSLOCK #undef CONFIG_CMD_TASKREADY #define CONFIG_CMD_TEMP_SENSOR #define CONFIG_CMD_TIMERINFO #undef CONFIG_CMD_TPM_LOG #define CONFIG_CMD_TYPEC #undef CONFIG_CMD_USART_INFO #define CONFIG_CMD_USBMUX #undef CONFIG_CMD_USB_PD_PE #define CONFIG_CMD_WAITMS /*****************************************************************************/ /* Provide common core code to output panic information without interrupts. */ #define CONFIG_COMMON_PANIC_OUTPUT /* * Store a panic log and halt the system for a software-related reasons, such as * stack overflow or assertion failure. */ #undef CONFIG_SOFTWARE_PANIC /* * Certain platforms(e.g. eve, poppy) cannot retain panic info in data ram since * VCC is powered down on EC reset. On such platforms, panic data needs to be * saved/restored to persistent storage by using chip specific * implementations. This option can be enabled by those platforms that have and * wish to use chip-implemented panic backup/restore functions. */ #undef CONFIG_CHIP_PANIC_BACKUP /* * Provide the default GPIO abstraction layer. * You want this unless you are doing a really tiny firmware. */ #define CONFIG_COMMON_GPIO /* * Provides smaller GPIO names to reduce flash size. Instead of the 'name' * field in GPIO macro it will concat 'port' and 'pin' to reduce flash size. */ #undef CONFIG_COMMON_GPIO_SHORTNAMES /* * EC's supporting powering down GPIO pins. * Add flag GPIO_POWER_DOWN and additional API's. */ #undef CONFIG_GPIO_POWER_DOWN /* * Provide common runtime layer code (tasks, hooks ...) * You want this unless you are doing a really tiny firmware. */ #define CONFIG_COMMON_RUNTIME /* Provide common core code to handle the operating system timers. */ #define CONFIG_COMMON_TIMER /*****************************************************************************/ /* * Make it possible for console to be output to different channels that can be * turned on and off. * * This is useful as a developer convenience when the console is crowded with * messages, to make it easier to use the interactive console. * FAFT and servod also use this feature. * * Boards may #undef this to reduce image size. */ #define CONFIG_CONSOLE_CHANNEL /* * Provide additional help on console commands, such as the supported * options/usage. * * Boards may #undef this to reduce image size. */ #define CONFIG_CONSOLE_CMDHELP /* * Add a .flags field to the console commands data structure, to distinguish * some commands from others. The available flags bits are defined in * include/console.h */ #undef CONFIG_CONSOLE_COMMAND_FLAGS /* * One use of the .flags field is to make some console commands restricted, so * that they can be disabled or enabled at run time. */ #undef CONFIG_RESTRICTED_CONSOLE_COMMANDS /* The default .flags field value is zero, unless overridden with this. */ #undef CONFIG_CONSOLE_COMMAND_FLAGS_DEFAULT /* * Enable EC_CMD_CONSOLE_READ V1. One could disable this config to prevent * kernel from creating the `console_log` debugfs entry. */ #define CONFIG_CONSOLE_ENABLE_READ_V1 /* * Number of entries in console history buffer. * * Boards may #undef this to reduce memory usage. */ #define CONFIG_CONSOLE_HISTORY 8 /* Max length of a single line of input */ #define CONFIG_CONSOLE_INPUT_LINE_SIZE 80 /* Enable verbose output to UART console and extra timestamp print precision. */ #define CONFIG_CONSOLE_VERBOSE /*****************************************************************************/ /* Support for EC-EC communication */ /* * Board is master or slave in EC-EC communication. */ #undef CONFIG_EC_EC_COMM_MASTER #undef CONFIG_EC_EC_COMM_SLAVE /* * Board support battery-related functions in EC-EC communication. */ #undef CONFIG_EC_EC_COMM_BATTERY /* * Enable the experimental console. * * NOTE: If you enable this experimental console, you will need to run the * EC-3PO interactive console in the util directory! Otherwise, you won't be * able to enter any commands. */ #undef CONFIG_EXPERIMENTAL_CONSOLE /* Include CRC-8 utility function */ #undef CONFIG_CRC8 /* * When enabled, do not build RO image from the same set of files as the RW * image. Instead define a separate set of object files in the respective * build.mk files by adding the objects to the custom-ro_objs-y variable. */ #undef CONFIG_CUSTOMIZED_RO /* * When enabled, build in support for software & hardware crypto; * only supported on CR50. */ #undef CONFIG_DCRYPTO /* * When enabled, accelerate sha512 using the generic crypto engine; * only supported on CR50 */ #undef CONFIG_DCRYPTO_SHA512 /* * When enabled build support for SHA-384/512, requires CONFIG_DCRYPTO. */ #undef CONFIG_UPTO_SHA512 /* * When enabled ignore version et al during fw upgrade for chip/g. */ #undef CONFIG_IGNORE_G_UPDATE_CHECKS /* * When enabled hardware alerts statistics provided via VendorCommand extension. */ #undef CONFIG_ENABLE_H1_ALERTS /* * Enable console shell command 'alerts' that prints chip alerts statistics. */ #undef CONFIG_ENABLE_H1_ALERTS_CONSOLE /*****************************************************************************/ /* * Debugging config * * Note that these options are enabled by default, because they're really * handy for debugging systems during bringup and even at factory time. * * A board may undefine any or all of these to reduce image size and RAM usage, * at the cost of debuggability. */ /* * ASSERT() macros are checked at runtime. See CONFIG_DEBUG_ASSERT_REBOOTS * to see what happens if one fails. * * Boards may #undef this to reduce image size. */ #define CONFIG_DEBUG_ASSERT /* * Prints a message and reboots if an ASSERT() macro fails at runtime. When * enabled, an ASSERT() which fails will produce a message of the form: * * ASSERTION FAILURE '' in function() at file:line * * If this is not defined, failing ASSERT() will trigger a BKPT instruction * instead. * * Ignored if CONFIG_DEBUG_ASSERT is not defined. * * Boards may #undef this to reduce image size. */ #define CONFIG_DEBUG_ASSERT_REBOOTS /* * On assertion failure, prints only the file name and the line number. * * Ignored if CONFIG_DEBUG_ASSERT_REBOOTS is not defined. * * Boards may define this to reduce image size. */ #undef CONFIG_DEBUG_ASSERT_BRIEF /* * Disable the write buffer used for default memory map accesses. * This turns "Imprecise data bus errors" into "Precise" errors * in exception traces at the cost of some performance. * This may help identify the offending instruction causing an * exception. Supported on cortex-m. */ #undef CONFIG_DEBUG_DISABLE_WRITE_BUFFER /* * Print additional information when exceptions are triggered, such as the * fault address, here shown as bfar. This shows the reason for the fault * and may help to determine the cause. * * === EXCEPTION: 03 ====== xPSR: 01000000 =========== * r0 :0000000b r1 :00000047 r2 :60000000 r3 :200013dd * r4 :00000000 r5 :080053f4 r6 :200013d0 r7 :00000002 * r8 :00000000 r9 :200013de r10:00000000 r11:00000000 * r12:00000000 sp :200009a0 lr :08002b85 pc :08003a8a * Precise data bus error, Forced hard fault, Vector catch, bfar = 60000000 * mmfs = 00008200, shcsr = 00000000, hfsr = 40000000, dfsr = 00000008 * * If this is not defined, only a register dump will be printed. * * Boards may #undef this to reduce image size. */ #define CONFIG_DEBUG_EXCEPTIONS /* * Print orientation when device orientation changes * (requires CONFIG_SENSOR_ORIENTATION) */ #undef CONFIG_DEBUG_ORIENTATION /* Support Synchronous UART debug printf. */ #undef CONFIG_DEBUG_PRINTF /* Check for stack overflows on every context switch */ #define CONFIG_DEBUG_STACK_OVERFLOW /*****************************************************************************/ /* Support events from devices attached to the EC */ #undef CONFIG_DEVICE_EVENT /* Monitor the states of other devices */ #undef CONFIG_DEVICE_STATE /* Support DMA transfers inside the EC */ #undef CONFIG_DMA /* Use the common interrupt handlers for DMA IRQs */ #define CONFIG_DMA_DEFAULT_HANDLERS /* Compile extra debugging and tests for the DMA module */ #undef CONFIG_DMA_HELP /* Support EC to Internal bus bridge. */ #undef CONFIG_EC2I /* Usually, EC capable of sensor speeds up to 200000 mHz */ #define CONFIG_EC_MAX_SENSOR_FREQ_DEFAULT_MILLIHZ 200000 /* Maximal EC sampling rate */ #undef CONFIG_EC_MAX_SENSOR_FREQ_MILLIHZ /* * Allow board to override the feature bitmap provided through host command * and ACPI. */ #undef CONFIG_EC_FEATURE_BOARD_OVERRIDE /* Support EC chip internal data EEPROM */ #undef CONFIG_EEPROM /* * Support for sending emulated sysrq events to AP (on designs with a keyboard, * sysrq is passed as normal key presses). */ #undef CONFIG_EMULATED_SYSRQ /* Support for eSPI for host communication */ #undef CONFIG_ESPI /* Use Virtual Wire signals instead of GPIO with eSPI interface */ #undef CONFIG_ESPI_VW_SIGNALS /* MCHP next two items are EC eSPI slave configuration */ /* Maximum clock frequence eSPI EC slave advertises * Values in MHz are 20, 25, 33, 50, and 66 */ #undef CONFIG_ESPI_EC_MAX_FREQ /* EC eSPI slave advertises IO lanes * 0 = Single * 1 = Single and Dual * 2 = Single and Quad * 3 = Single, Dual, and Quad */ #undef CONFIG_ESPI_EC_MODE /* Bit map of eSPI channels EC advertises * bit[0] = 1 Peripheral channel * bit[1] = 1 Virtual Wire channel * bit[2] = 1 OOB channel * bit[3] = 1 Flash channel */ #undef CONFIG_ESPI_EC_CHAN_BITMAP /* Use Virtual Wire for Platform Reset instead of a sideband signal */ #undef CONFIG_ESPI_PLTRST_IS_VWIRE /* Include code for handling external power */ #define CONFIG_EXTPOWER /* Support detecting external power presence via a GPIO */ #undef CONFIG_EXTPOWER_GPIO /* Default debounce time for external power signal */ #define CONFIG_EXTPOWER_DEBOUNCE_MS 30 /*****************************************************************************/ /* Number of cooling fans. Undef if none. */ #undef CONFIG_FANS /* Percentage to which all fans are set at initiation */ #define CONFIG_FAN_INIT_SPEED 100 /* Support fan control while in low-power idle */ #undef CONFIG_FAN_DSLEEP /* * Replace the default fan_percent_to_rpm() function with a board-specific * implementation in board.c */ #undef CONFIG_FAN_RPM_CUSTOM /* * We normally check and update the fans once per second (HOOK_SECOND). If this * is #defined to a postive integer N, we will only update the fans every N * seconds instead. */ #undef CONFIG_FAN_UPDATE_PERIOD /* Send event when mode change, host read acpi memory and select DPTF table */ #undef CONFIG_DPTF_DEVICE_ORIENTATION /*****************************************************************************/ /* Flash configuration */ /* This enables console commands and higher-level features */ #define CONFIG_FLASH /* This enables chip-specific access functions */ #define CONFIG_FLASH_PHYSICAL #undef CONFIG_FLASH_BANK_SIZE #undef CONFIG_FLASH_ERASED_VALUE32 #undef CONFIG_FLASH_ERASE_SIZE #undef CONFIG_FLASH_ROW_SIZE /* Allow deferred (async) flash erase */ #undef CONFIG_FLASH_DEFERRED_ERASE /* Flash must be selected for write/erase operations to succeed. */ #undef CONFIG_FLASH_SELECT_REQUIRED /* Base address of program memory */ #undef CONFIG_PROGRAM_MEMORY_BASE /* * EC code can reside on internal or external storage. Only one of these * CONFIGs should be defined. */ #undef CONFIG_EXTERNAL_STORAGE #undef CONFIG_INTERNAL_STORAGE /* * Flash is directly mapped into the EC's address space. If this is not * defined, the flash driver must implement flash_physical_read(). */ #define CONFIG_MAPPED_STORAGE /* * Base address of memory-mapped flash storage, for platforms which define * CONFIG_MAPPED_STORAGE. */ #undef CONFIG_MAPPED_STORAGE_BASE #undef CONFIG_FLASH_PROTECT_NEXT_BOOT /* * Some platforms need to write protect RW independently of all flash. */ #undef CONFIG_FLASH_PROTECT_RW /* * Store persistent write protect for the flash inside the flash data itself. * This allows ECs with internal flash to emulate something closer to a SPI * flash write protect register. If this is not defined, write protect state * is maintained solely by the physical flash driver. */ #define CONFIG_FLASH_PSTATE /* * Store the pstate data in its own dedicated bank of flash. This allows * disabling the protect-RO-at-boot flag without rewriting the RO firmware, * but costs a bank of flash. * * If this is not defined, the pstate data is stored inside the RO firmware * image itself. This is more space-efficient, but the only way to clear the * flag once it's set is to rewrite the RO firmware (after removing the WP * screw, of course). */ #define CONFIG_FLASH_PSTATE_BANK /* * Lock the PSTATE by default (currently only supported when * CONFIG_FLASH_PSTATE_BANK is not defined). */ #undef CONFIG_FLASH_PSTATE_LOCKED /* * For flash that is segemented in different regions. */ #undef CONFIG_FLASH_MULTIPLE_REGION /* Number of regions of different size/type */ #undef CONFIG_FLASH_REGION_TYPE_COUNT /* Total size of writable flash */ #undef CONFIG_FLASH_SIZE /* Minimum flash write size (in bytes) */ #undef CONFIG_FLASH_WRITE_SIZE /* Most efficient flash write size (in bytes) */ #undef CONFIG_FLASH_WRITE_IDEAL_SIZE /* Protected region of storage belonging to EC */ #undef CONFIG_EC_PROTECTED_STORAGE_OFF #undef CONFIG_EC_PROTECTED_STORAGE_SIZE /* Writable region of storage belonging to EC */ #undef CONFIG_EC_WRITABLE_STORAGE_OFF #undef CONFIG_EC_WRITABLE_STORAGE_SIZE /* Enable robust non-volatile counter in flash */ #undef CONFIG_FLASH_NVCOUNTER /* Address of start of the NVcounter flash page */ #undef CONFIG_FLASH_NVCTR_BASE_A #undef CONFIG_FLASH_NVCTR_BASE_B /*****************************************************************************/ /* NvMem Configuration */ /* Enable NV Memory module within flash */ #undef CONFIG_FLASH_NVMEM /* Offset to start of NvMem area from base of flash */ #undef CONFIG_FLASH_NVMEM_OFFSET_A #undef CONFIG_FLASH_NVMEM_OFFSET_B /* Address of start of Nvmem area */ #undef CONFIG_FLASH_NVMEM_BASE_A #undef CONFIG_FLASH_NVMEM_BASE_B /* Size in bytes of NvMem area */ #undef CONFIG_FLASH_NVMEM_SIZE /* Enable variable support (requires CONFIG_FLASH_NVMEM) */ #undef CONFIG_FLASH_NVMEM_VARS /* * We already have to define nvmem_user_sizes[] to specify the order and size * of the user regions. CONFIG_FLASH_NVMEM_VARS looks for two symbols to * specify the region number and size for the variable region. */ #undef CONFIG_FLASH_NVMEM_VARS_USER_NUM #undef CONFIG_FLASH_NVMEM_VARS_USER_SIZE /*****************************************************************************/ /* Include a flashmap in the compiled firmware image */ #define CONFIG_FMAP /* Allow EC serial console input to wake up the EC from STOP mode */ #undef CONFIG_FORCE_CONSOLE_RESUME /* Enable support for floating point unit */ #undef CONFIG_FPU /*****************************************************************************/ /* Firmware region configuration */ #undef CONFIG_FW_PSTATE_OFF #undef CONFIG_FW_PSTATE_SIZE /* * Reuse the space that was occupied in RAM by the little firmware (LFW) loader * with the section ".bss.slow" instead. */ #undef CONFIG_REPLACE_LOADER_WITH_BSS_SLOW /* * Read-only / read-write image configuration. * Images may reside on storage (ex. external or internal SPI) at a different * offset than when copied to program memory. Hence, two sets of offsets, * for STORAGE and for MEMORY. */ #undef CONFIG_RO_MEM_OFF /* Offset relative to CONFIG_EC_PROTECTED_STORAGE_OFF */ #undef CONFIG_RO_STORAGE_OFF #undef CONFIG_RO_SIZE #undef CONFIG_RW_MEM_OFF /* Some targets include two RW sections in the image. */ #undef CONFIG_RW_B /* This is the offset of the second RW section into the flash. */ #undef CONFIG_RW_B_MEM_OFF /* Offset relative to CONFIG_EC_WRITABLE_STORAGE_OFF */ #undef CONFIG_RW_STORAGE_OFF #undef CONFIG_RW_SIZE /* * NPCX-specific bootheader geometry. * TODO(crosbug.com/p/23796): Factor these CONFIGs out. */ #undef CONFIG_RO_HDR_MEM_OFF #undef CONFIG_RO_HDR_SIZE /* * Write protect region offset / size. This region normally encompasses the * RO image, but may also contain additional images or data. */ #undef CONFIG_WP_STORAGE_OFF #undef CONFIG_WP_STORAGE_SIZE /* * Rollback protect region. If CONFIG_ROLLBACK is defined to enable the rollback * protect region, CONFIG_ROLLBACK_OFF and CONFIG_ROLLBACK_SIZE must be defined * too. */ #undef CONFIG_ROLLBACK #undef CONFIG_ROLLBACK_OFF #undef CONFIG_ROLLBACK_SIZE /* If defined, add support for storing some entropy in the rollback region. */ #undef CONFIG_ROLLBACK_SECRET_SIZE /* * If defined, inject some locally generated entropy when secret is updated, * using board_get_entropy function. * Large values may take a long time to generate. */ #undef CONFIG_ROLLBACK_SECRET_LOCAL_ENTROPY_SIZE /* If defined, we can update rollback information (RW can unset this). */ #define CONFIG_ROLLBACK_UPDATE /* * Current rollback version. Meaningless for RO (but provides the minimum value * that will be written to the rollback protection at flash time). * * For RW, rollback version included in version structure, used by RO to * determine if the RW image is recent enough and can be jumped to. * * Valid values are >= 0, <= INT32_MAX (positive, 32-bit signed integer). */ #define CONFIG_ROLLBACK_VERSION 0 /* * Board Image ec.bin contains a RO firmware. If not defined, the image will * only contain the RW firmware. The RO firmware comes from another board. */ #define CONFIG_FW_INCLUDE_RO /* If defined, another image (RW) exists with more features */ #undef CONFIG_FW_LIMITED_IMAGE /* * If defined, we can use system_get_fw_reset_vector function to decide * reset vector of RO/RW firmware for sysjump. */ #undef CONFIG_FW_RESET_VECTOR /*****************************************************************************/ /* Motion sensor based gesture recognition information */ /* These all require HAS_TASK_MOTIONSENSE to work */ /* Do we want to detect gestures? */ #undef CONFIG_GESTURE_DETECTION /* Mask of all sensors used for gesture dectections */ #undef CONFIG_GESTURE_DETECTION_MASK /* some gesture recognition done in software */ #undef CONFIG_GESTURE_SW_DETECTION /* enable gesture host interface */ #undef CONFIG_GESTURE_HOST_DETECTION /* Sensor sampling interval for gesture recognition */ #undef CONFIG_GESTURE_SAMPLING_INTERVAL_MS /* Which sensor to look for battery tap recognition */ #undef CONFIG_GESTURE_SENSOR_BATTERY_TAP /* * Double tap detection parameters * Double tap works by looking for two isolated Z-axis accelerometer impulses * preceded and followed by relatively calm periods of accelerometer motion. * * Define an outer and inner window. The inner window specifies how * long the tap impulse is expected to last. The outer window specifies the * period before the initial tap impluse and after the final tap impulse for * which to check for relatively calm periods. In between the two impulses * there is a minimum and maximum interstice time allowed. * * Define an acceleration threshold to dectect a tap, in mg. */ #undef CONFIG_GESTURE_TAP_OUTER_WINDOW_T #undef CONFIG_GESTURE_TAP_INNER_WINDOW_T #undef CONFIG_GESTURE_TAP_MIN_INTERSTICE_T #undef CONFIG_GESTURE_TAP_MAX_INTERSTICE_T #undef CONFIG_GESTURE_TAP_THRES_MG /* Event generated when battery tap is detected */ #undef CONFIG_GESTURE_TAP_EVENT /* Which sensor to look for significant motion activity */ #undef CONFIG_GESTURE_SIGMO /* * Significant motion parameters * Sigmo state machine looks for movement, waits skip milli-seconds, * and check for movement again with proof milli-seconds. */ #undef CONFIG_GESTURE_SIGMO_PROOF_MS #undef CONFIG_GESTURE_SIGMO_SKIP_MS #undef CONFIG_GESTURE_SIGMO_THRES_MG /* Event generated when significant motion is detected. */ #undef CONFIG_GESTURE_SIGMO_EVENT /* Do we want to detect the lid angle? */ #undef CONFIG_LID_ANGLE /* * Add code for preventing 0 and 360 degree transition. Needed when * Device supports tablet mode. */ #undef CONFIG_LID_ANGLE_INVALID_CHECK /* * Use lid angle to detect tablet mode. */ #undef CONFIG_LID_ANGLE_TABLET_MODE /* Which sensor is located on the base? */ #undef CONFIG_LID_ANGLE_SENSOR_BASE /* Which sensor is located on the lid? */ #undef CONFIG_LID_ANGLE_SENSOR_LID /* * Allows using the lid angle measurement to determine if peripheral devices * should be enabled or disabled, like key scanning, trackpad interrupt. */ #undef CONFIG_LID_ANGLE_UPDATE /* * During shutdown sequence sensor rails can be powered down asynchronously * to the EC hence EC cannot interlock the sensor states with the power down * states. To avoid this issue, defer switching the sensors rate with a * configurable delay if in S3. By the time deferred function is serviced, * if the chipset is in S5 we can back out from switching the sensor rate. */ #define CONFIG_MOTION_SENSE_SUSPEND_DELAY_US 0 /* Define motion sensor count in board layer */ #undef CONFIG_DYNAMIC_MOTION_SENSOR_COUNT /******************************************************************************/ /* Host to RAM (H2RAM) Memory Mapping */ /* H2RAM Base memory address */ #undef CONFIG_H2RAM_BASE /* H2RAM Size */ #undef CONFIG_H2RAM_SIZE /* H2RAM Host LPC I/O base memory address */ #undef CONFIG_H2RAM_HOST_LPC_IO_BASE /* ISH boot start address */ #undef CONFIG_ISH_BOOT_START /* * Define the minimal amount of time (in ms) betwen running motion sense task * loop. */ #define CONFIG_MOTION_MIN_SENSE_WAIT_TIME 3 /*****************************************************************************/ /* * Support the host asking the EC about the status of the most recent host * command. * * When the AP is attached to the EC via a serialized bus such as I2C or SPI, * it needs a way to minimize the length of time an EC command will tie up the * bus (and the kernel driver on the AP). If this config is defined, the EC * may return an in-progress result code for slow commands such as flash * erase/write instead of stalling until the command finishes processing, and * the AP may then inquire the status of the current command and/or the result * of the previous command. */ #undef CONFIG_HOST_COMMAND_STATUS /* clear bit(s) to mask reporting of an EC_HOST_EVENT_XXX event(s) */ #define CONFIG_HOST_EVENT_REPORT_MASK 0xffffffff #define CONFIG_HOST_EVENT64_REPORT_MASK 0xffffffffffffffffULL /* Config option to support 64-bit hostevents and wake-masks. */ #define CONFIG_HOST_EVENT64 /* * The host commands are sorted in the .rodata.hcmds section so use the binary * search algorithm to match a command to its handler */ #undef CONFIG_HOSTCMD_SECTION_SORTED /* * Host command parameters and response are 32-bit aligned. This generates * much more efficient code on ARM. */ #undef CONFIG_HOSTCMD_ALIGNED /* * Include host commands to fetch battery information from * ec_response_battery_static/dynamic_info structures, only makes sense when * CONFIG_BATTERY_V2 is enabled. */ #undef CONFIG_HOSTCMD_BATTERY_V2 /* Default hcdebug mode, e.g. HCDEBUG_OFF or HCDEBUG_NORMAL */ #define CONFIG_HOSTCMD_DEBUG_MODE HCDEBUG_NORMAL /* If we have host command task, assume we also are using host events. */ #ifdef HAS_TASK_HOSTCMD #define CONFIG_HOSTCMD_EVENTS #else #undef CONFIG_HOSTCMD_EVENTS #endif /* * Board supports host command to get EC SPI flash info. This is typically * only needed if the factory needs to determine which of several possible SPI * flash chips is attached to the EC on a given board. */ #undef CONFIG_HOSTCMD_FLASH_SPI_INFO /* * For ECs where the host command interface is I2C, slave * address which the EC will respond to. */ #undef CONFIG_HOSTCMD_I2C_SLAVE_ADDR /* * Accept EC host commands over the SPI slave (SPS) interface. */ #undef CONFIG_HOSTCMD_SPS /* * Host command rate limiting assures EC will have time to process lower * priority tasks even if the AP is hammering the EC with host commands. * If there is less than CONFIG_HOSTCMD_RATE_LIMITING_MIN_REST between * host commands for CONFIG_HOSTCMD_RATE_LIMITING_PERIOD, then a * recess period of CONFIG_HOSTCMD_RATE_LIMITING_RECESS will be * enforced. */ #define CONFIG_HOSTCMD_RATE_LIMITING_PERIOD (500 * MSEC) #define CONFIG_HOSTCMD_RATE_LIMITING_MIN_REST (3 * MSEC) #define CONFIG_HOSTCMD_RATE_LIMITING_RECESS (20 * MSEC) /* PD MCU supports host commands */ #undef CONFIG_HOSTCMD_PD /* EC supports EC_CMD_PD_CHIP_INFO */ #define CONFIG_EC_CMD_PD_CHIP_INFO /* * Use if PD MCU controls charging (selecting charging port and input * current limit). */ #undef CONFIG_HOSTCMD_PD_CHG_CTRL /* Panic when status of PD MCU reflects that it has crashed */ #undef CONFIG_HOSTCMD_PD_PANIC /* Board supports RTC host commands */ #undef CONFIG_HOSTCMD_RTC /* For access to VBNV on-EC battery-backed storage */ #undef CONFIG_HOSTCMD_VBNV_CONTEXT /* EC controls the board's SKU ID and can report that to the AP */ #undef CONFIG_HOSTCMD_SKUID /* Set SKU ID from AP */ #undef CONFIG_HOSTCMD_AP_SET_SKUID /* List of host commands whose debug output will be suppressed */ #undef CONFIG_SUPPRESSED_HOST_COMMANDS /*****************************************************************************/ /* Enable debugging and profiling statistics for hook functions */ #undef CONFIG_HOOK_DEBUG /*****************************************************************************/ /* CRC configuration */ /* Enable the hardware accelerator for CRC computation */ #undef CONFIG_HW_CRC /* Enable the software routine for CRC computation */ #undef CONFIG_SW_CRC /*****************************************************************************/ /* Enable system hibernate */ #define CONFIG_HIBERNATE /* Default delay after shutting down before hibernating */ #define CONFIG_HIBERNATE_DELAY_SEC 3600 /* * Use to define going in to hibernate early if low on battery. * CONFIG_HIBERNATE_BATT_PCT specifies the low battery threshold * for going into hibernate early, and CONFIG_HIBERNATE_BATT_SEC defines * the minimum amount of time to stay in G3 before checking for low * battery hibernate. */ #undef CONFIG_HIBERNATE_BATT_PCT #undef CONFIG_HIBERNATE_BATT_SEC /* For ECs with multiple wakeup pins, define enabled wakeup pins */ #undef CONFIG_HIBERNATE_WAKEUP_PINS /* * If defined, chip hibernation is used. Your board needs to define wake-up * signals. Undefine this to use board hibernation capability. */ #define CONFIG_SUPPORT_CHIP_HIBERNATION /* * Use PSL (Power Switch Logic) for hibernating. It turns off VCC power rail * for ultra-low power consumption and uses PSL inputs rely on VSBY power rail * to wake up ec and the whole system. */ #undef CONFIG_HIBERNATE_PSL /* Use a hardware specific udelay(). */ #undef CONFIG_HW_SPECIFIC_UDELAY /*****************************************************************************/ /* I2C configuration */ #undef CONFIG_I2C #undef CONFIG_I2C_DEBUG #undef CONFIG_I2C_DEBUG_PASSTHRU #undef CONFIG_I2C_PASSTHROUGH #undef CONFIG_I2C_PASSTHRU_RESTRICTED #undef CONFIG_I2C_VIRTUAL_BATTERY /* * Conservative I2C reading size per single transaction. For example, register * of stm32f0 and stm32l4 are limited to be 8 bits for this field. */ #define CONFIG_I2C_CHIP_MAX_READ_SIZE 255 /* * Enable i2c_xfer() for receiving request larger than * CONFIG_I2C_CHIP_MAX_READ_SIZE. */ #undef CONFIG_I2C_XFER_LARGE_READ /* * If defined, makes i2c_xfer callback into board-provided functions before the * start and after the end of every I2C transaction. This can be used by boards * to implement any I2C device specific quirks e.g. requiring minimum bus-free * time between every I2C transaction with a device. */ #undef CONFIG_I2C_XFER_BOARD_CALLBACK /* EC uses an I2C master interface */ #undef CONFIG_I2C_MASTER /* EC uses an I2C slave interface */ #undef CONFIG_I2C_SLAVE /* Defines I2C operation retry count when slave nack'd(EC_ERROR_BUSY) */ #define CONFIG_I2C_NACK_RETRY_COUNT 0 /* * I2C SCL gating. * * If CONFIG_I2C_SCL_GATE_ADDR/PORT is defined, whenever the defined address * is addressed, CONFIG_I2C_SCL_GATE_GPIO is set to high. When the I2C * transaction is done, the pin is set back to low. */ #undef CONFIG_I2C_SCL_GATE_PORT #undef CONFIG_I2C_SCL_GATE_ADDR #undef CONFIG_I2C_SCL_GATE_GPIO /* * Some chip supports two owned slave address. The second slave address is used * for other purpose such as board specific i2c commands. This option can be * set if user of the second slave address requires larger host packet buffer * size. */ #define CONFIG_I2C_EXTRA_PACKET_SIZE 0 /* * I2C multi-port controller. * * If CONFIG_I2C_MULTI_PORT_CONTROLLER is defined, a single on-chip I2C * controller may have multiple I2C ports attached. Therefore, I2c operations * must lock the controller (not just the port) to prevent hardware access * conflicts. */ #undef CONFIG_I2C_MULTI_PORT_CONTROLLER /*****************************************************************************/ /* Current/Power monitor */ /* * Compile driver for INA219 or INA231. These two flags may not be both * defined. */ #undef CONFIG_INA219 #undef CONFIG_INA231 /*****************************************************************************/ /* Inductive charging */ /* Enable inductive charging support */ #undef CONFIG_INDUCTIVE_CHARGING /******************************************************************************/ /* Support NXP PCA9534 I/O expander. */ #undef CONFIG_IO_EXPANDER_PCA9534 /*****************************************************************************/ /* Number of IRQs supported on the EC chip */ #undef CONFIG_IRQ_COUNT /* * The IT8320 supports e-flash clock up to 48 MHz (IT8390 maximum is 32 MHz). * Enable it if we want better performance of fetching instruction from e-flash. * * This is valid with PLL frequency equal to 48/96MHz only. */ #undef CONFIG_IT83XX_FLASH_CLOCK_48MHZ /* To define it, if I2C channel C and PECI used at the same time. */ #undef CONFIG_IT83XX_SMCLK2_ON_GPC7 /*****************************************************************************/ /* Keyboard config */ /* * The Silego reset chip sits in between the EC and the physical keyboard on * column 2. To save power in low-power modes, some Silego variants require * the signal to be inverted so that the open-drain output from the EC isn't * costing power due to the pull-up resistor in the Silego. */ #undef CONFIG_KEYBOARD_COL2_INVERTED /* * Keyboards with the assistant key also move the refresh key matrix to row 3 * instead of row 2. This is used by the boot key detection code to determine * if the refresh key is held down at boot. */ #undef CONFIG_KEYBOARD_REFRESH_ROW3 /* * Config KSO to start from a different KSO pin. This is to allow some chips * to use alternate functions on KSO pins. */ #define CONFIG_KEYBOARD_KSO_BASE 0 /* * For certain board configurations, KSI2 will be stuck asserted for all * scan columns if the power button is held. We must be aware of this case * in order to correctly handle recovery mode key combinations. */ #undef CONFIG_KEYBOARD_PWRBTN_ASSERTS_KSI2 /* Enable extra debugging output from keyboard modules */ #undef CONFIG_KEYBOARD_DEBUG /* The board uses a negative edge-triggered GPIO for keyboard interrupts. */ #undef CONFIG_KEYBOARD_IRQ_GPIO /* Compile code for 8042 keyboard protocol */ #undef CONFIG_KEYBOARD_PROTOCOL_8042 /* Compile code for MKBP keyboard protocol */ #undef CONFIG_KEYBOARD_PROTOCOL_MKBP /* Support keyboard factory test scanning */ #undef CONFIG_KEYBOARD_FACTORY_TEST /* * Keyboard config (struct keyboard_scan_config) is in board.c. If this is * not defined, default values from common/keyboard_scan.c will be used. */ #undef CONFIG_KEYBOARD_BOARD_CONFIG /* * Support for boot key combinations (e.g. refresh key being held on boot to * trigger recovery). */ #define CONFIG_KEYBOARD_BOOT_KEYS /* Add support for the assistant key. */ #undef CONFIG_KEYBOARD_ASSISTANT_KEY /* * Minimum CPU clocks between scans. This ensures that keyboard scanning * doesn't starve the other EC tasks of CPU when running at a decreased system * clock. */ #undef CONFIG_KEYBOARD_POST_SCAN_CLOCKS /* Print keyboard scan time intervals. */ #undef CONFIG_KEYBOARD_PRINT_SCAN_TIMES /* * Support for extra runtime key combinations (e.g. alt+volup+h/r for hibernate * and warm reboot, respectively). */ #define CONFIG_KEYBOARD_RUNTIME_KEYS /* * Allow the keyboard scan code set tables to be modified at runtime. */ #undef CONFIG_KEYBOARD_SCANCODE_MUTABLE /* * Call board-supplied keyboard_suppress_noise() function when the debounced * keyboard state changes. Some boards use this to send a signal to the audio * codec to suppress typing noise picked up by the microphone. */ #undef CONFIG_KEYBOARD_SUPPRESS_NOISE /* * Enable keyboard testing functionality. This enables a message which receives * a list of keyscan events from the AP and processes them. This will cause * keypresses to appear on the AP through the same mechanism as a normal * keyboard press. * * This can be used to spoof keyboard events, so is not normally defined, * except during internal testing. */ #undef CONFIG_KEYBOARD_TEST /* * Enable quasi-bidirectional buffers for KSO pins. It has an open-drain output * and a low-impedance pull-up. The low-impedance pull-up is active when ec * changes the output data buffers from 0 to 1, thereby reducing the * low-to-high transition time. */ #undef CONFIG_KEYBOARD_KSO_HIGH_DRIVE /*****************************************************************************/ /* Support common LED interface */ #undef CONFIG_LED_COMMON /* Standard LED behavior according to spec given that we have a red-green * bicolor led for charging and one power led */ #undef CONFIG_LED_POLICY_STD /* * Support common PWM-controlled LEDs that conform to the Chrome OS LED * behaviour specification. */ #undef CONFIG_LED_PWM /* * Here are some recommended color settings by default, but a board can change * the colors to one of "enum ec_led_colors" as they see fit. */ #define CONFIG_LED_PWM_CHARGE_COLOR EC_LED_COLOR_AMBER #define CONFIG_LED_PWM_NEAR_FULL_COLOR EC_LED_COLOR_GREEN #define CONFIG_LED_PWM_CHARGE_ERROR_COLOR EC_LED_COLOR_RED #define CONFIG_LED_PWM_SOC_ON_COLOR EC_LED_COLOR_GREEN #define CONFIG_LED_PWM_SOC_SUSPEND_COLOR EC_LED_COLOR_GREEN #define CONFIG_LED_PWM_LOW_BATT_COLOR EC_LED_COLOR_AMBER /* * How many PWM LEDs does the system have that will be controlled by the common * PWM LED policy? Currently, this may be at most 2. */ #undef CONFIG_LED_PWM_COUNT /* * LEDs for LED_POLICY STD may be inverted. In this case they are active low * and the GPIO names will be GPIO_LED..._L. */ #undef CONFIG_LED_BAT_ACTIVE_LOW #undef CONFIG_LED_POWER_ACTIVE_LOW /* Support for LED driver chip(s) */ #undef CONFIG_LED_DRIVER_DS2413 /* Maxim DS2413, on one-wire interface */ #undef CONFIG_LED_DRIVER_LM3509 /* LM3509, on I2C interface */ #undef CONFIG_LED_DRIVER_LM3630A /* LM3630A, on I2C interface */ #undef CONFIG_LED_DRIVER_LP5562 /* LP5562, on I2C interface */ /* Offset in flash where little firmware will live. */ #undef CONFIG_LFW_OFFSET /* * Compile lid switch support. * * This is enabled by default because all boards other than reference boards * are for laptops with lid switchs. Reference boards #undef it. */ #define CONFIG_LID_SWITCH /* * GPIOs to use to detect that the lid is opened. * * This is a X-macro composed of a list of LID_OPEN(GPIO_xxx) elements defining * all the GPIOs to check to find whether the lid is currently opened. * If not defined, it is using GPIO_LID_OPEN. */ #undef CONFIG_LID_SWITCH_GPIO_LIST /* * Support for turning the lightbar power rails on briefly when the AP is off. * Enabling this requires implementing the board-specific lb_power() function * to do it (see lb_common.h). */ #undef CONFIG_LIGHTBAR_POWER_RAILS /* * For tap sequence, show the last segment in dim to give a better idea of * battery percentage. */ #undef CONFIG_LIGHTBAR_TAP_DIM_LAST_SEGMENT /* * Adds a console command for testing the long long shift right ABI on Cortex-m4 * (Cr50). */ #undef CONFIG_LLSR_TEST /* Program memory offset for little firmware loader. */ #undef CONFIG_LOADER_MEM_OFF /* Size of little firmware loader. */ #undef CONFIG_LOADER_SIZE /* Little firmware loader storage offset. */ #undef CONFIG_LOADER_STORAGE_OFF /* * Low power idle options. These are disabled by default and all boards that * want to use low power idle must define it. When using the LFIOSC, the low * frequency clock will be used to conserve even more power when possible. * * GPIOs which need to trigger interrupts in low power idle must specify the * GPIO_INT_DSLEEP flag in gpio_list[]. * * Note that for some processors (e.g. LM4), an active JTAG connection will * prevent the EC from using low-power idle. */ #undef CONFIG_LOW_POWER_IDLE #undef CONFIG_LOW_POWER_USE_LFIOSC /* * Enable deep sleep during S0 (ignores SLEEP_MASK_AP_RUN). */ #undef CONFIG_LOW_POWER_S0 /* Support LPC interface */ #undef CONFIG_LPC /* Base address of low power RAM. */ #undef CONFIG_LPRAM_BASE /* Size of low power RAM. */ #undef CONFIG_LPRAM_SIZE /* Use Link-Time Optimizations to try to reduce the firmware code size */ #undef CONFIG_LTO /* Provide rudimentary malloc/free like services for shared memory. */ #undef CONFIG_MALLOC /* Need for a math library */ #undef CONFIG_MATH_UTIL /* Include code to do online compass calibration */ #undef CONFIG_MAG_CALIBRATE /* Presence of a Bosh Sensortec BMM150 magnetometer behind a BMI160. */ #undef CONFIG_MAG_BMI160_BMM150 /* Microchip EC SRAM start address */ #undef CONFIG_MEC_SRAM_BASE_START /* Microchip EC SRAM end address */ #undef CONFIG_MEC_SRAM_BASE_END /* Microchip EC SRAM size */ #undef CONFIG_MEC_SRAM_SIZE /* * Define Megachips DisplayPort to HDMI protocol converter/level shifter serial * interface. */ #undef CONFIG_MCDP28X0 /* Define clock input to MFT module. */ #undef CONFIG_MFT_INPUT_LFCLK /* Support MKBP event */ #undef CONFIG_MKBP_EVENT /* MKBP events are sent using host event */ #undef CONFIG_MKBP_USE_HOST_EVENT /* * With this option, we can define the MKBP wakeup events in this mask (as a * white list) in board level, those events allow to interrupt AP during S3. */ #undef CONFIG_MKBP_WAKEUP_MASK /* Support memory protection unit (MPU) */ #undef CONFIG_MPU /* Do not try hold I/O pins at frozen level during deep sleep */ #undef CONFIG_NO_PINHOLD /* Support one-wire interface */ #undef CONFIG_ONEWIRE /* Support One Time Protection structure */ #undef CONFIG_OTP /* Support PECI interface to x86 processor */ #undef CONFIG_PECI /* * Maximum operating temperature in degrees Celcius used on some x86 * processors. CPU chip temperature is reported relative to this value and * is never reported greater than this value. Processor asserts PROCHOT# * and starts throttling frequency and voltage at this temp. Operation may * become unreliable if temperature exceeds this limit. */ #undef CONFIG_PECI_TJMAX /* Support physical presence detection (via a physical button) */ #undef CONFIG_PHYSICAL_PRESENCE /* Enable (unsafe!) developer debug features for physical presence */ #undef CONFIG_PHYSICAL_PRESENCE_DEBUG_UNSAFE /*****************************************************************************/ /* PMU config */ /* * Enable hard-resetting the PMU from the EC. The implementation is rather * hacky; it simply shorts out the 3.3V rail to force the PMIC to panic. We * need this unfortunate hack because it's the only way to reset the I2C engine * inside the PMU. */ #undef CONFIG_PMU_HARD_RESET /* * Enable this config to make console UART self sufficient (no other * initialization required before uart_init(), no interrupts, uart_tx_char() * does not exit until character finished transmitting). * * This is useful during early hardware bringup, each platform needs to * implement its own code to support this. */ #undef CONFIG_POLLING_UART /* Define length of history buffer for port80 messages. */ #define CONFIG_PORT80_HISTORY_LEN 128 /* * Enable/Disable printing of port80 messages in interrupt context. By default, * this is disabled. */ #define CONFIG_PORT80_PRINT_IN_INT 0 /* Compile common code to support power button debouncing */ #undef CONFIG_POWER_BUTTON /* Force the active state of the power button : 0(default if unset) or 1 */ #undef CONFIG_POWER_BUTTON_ACTIVE_STATE /* Allow the power button to send events while the lid is closed */ #undef CONFIG_POWER_BUTTON_IGNORE_LID /* Support sending the power button signal to x86 chipsets */ #undef CONFIG_POWER_BUTTON_X86 /* Set power button state idle at init. Implemented only for npcx. */ #undef CONFIG_POWER_BUTTON_INIT_IDLE /* * Enable delay between DSW_PWROK and PWRBTN assertion. * If enabled, DSW_PWROK_TO_PWRBTN_US and get_time_dsw_pwrok must be defined * as well. */ #undef CONFIG_DELAY_DSW_PWROK_TO_PWRBTN /* * The time in usec required for PMC to be ready to detect power button press. * Refer to the timing diagram for G3 to S0 on PDG for details. */ #define CONFIG_DSW_PWROK_TO_PWRBTN_US (95 * MSEC) /* Compile common code for AP power state machine */ #undef CONFIG_POWER_COMMON /* Disable the power-on transition when the lid is opened */ #undef CONFIG_POWER_IGNORE_LID_OPEN /* Enable a task-safe way to control the PP5000 rail. */ #undef CONFIG_POWER_PP5000_CONTROL /* Support stopping in S5 on shutdown */ #undef CONFIG_POWER_SHUTDOWN_PAUSE_IN_S5 /* * Detect power signal interrupt storms, defined as more than * CONFIG_POWER_SIGNAL_INTERRUPT_STORM_DETECT_THRESHOLD occurences of a single * power signal interrupt within one second. */ #undef CONFIG_POWER_SIGNAL_INTERRUPT_STORM_DETECT_THRESHOLD /* Use part of the EC's data EEPROM to hold persistent storage for the AP. */ #undef CONFIG_PSTORE /* Support S0ix */ #undef CONFIG_POWER_S0IX /* * Allow the host to self-report its sleep state, in case there is some delay * between the host beginning to enter the sleep state and power signals * actually reflecting the new state. */ #undef CONFIG_POWER_TRACK_HOST_SLEEP_STATE /* * Implement the '%li' printf format as a *32-bit* integer format, * as it might be expected by non-EC code. */ #undef CONFIG_PRINTF_LEGACY_LI_FORMAT /*****************************************************************************/ /* Support PWM control */ #undef CONFIG_PWM /* Define clock input to PWM module. */ #undef CONFIG_PWM_INPUT_LFCLK /*****************************************************************************/ /* Support PWM output to display backlight */ #undef CONFIG_PWM_DISPLIGHT /* Support PWM output to keyboard backlight */ #undef CONFIG_PWM_KBLIGHT /* Base address of RAM for the chip */ #undef CONFIG_RAM_BASE /* * CONFIG_DATA_RAM_SIZE and CONFIG_RAM_SIZE indicate size of all data RAM * available on the chip in bytes and size of data RAM available for EC in * bytes, respectively. * Usually, CONFIG_DATA_RAM_SIZE = CONFIG_RAM_SIZE but some chips need to * allocate RAM for the mask ROM. Then CONFIG_DATA_RAM_SIZE > CONFIG_RAM_SIZE. */ #undef CONFIG_DATA_RAM_SIZE #undef CONFIG_RAM_SIZE /* Enable rbox peripheral */ #undef CONFIG_RBOX /* Enable RDD peripheral */ #undef CONFIG_RDD /* Support IR357x Link voltage regulator debugging / reprogramming */ #undef CONFIG_REGULATOR_IR357X /* Support RMA auth challenge-response */ #undef CONFIG_RMA_AUTH /* If that's defined, the server public key and ID must also be defined */ #undef CONFIG_RMA_AUTH_SERVER_PUBLIC_KEY /* 32 bytes: {0xNN, 0xNN, ... 0xNN} */ #undef CONFIG_RMA_AUTH_SERVER_KEY_ID /* 6-bit key ID, 0xMM */ /* Enable hardware Random Number generator support */ #undef CONFIG_RNG /* Support verifying 2048-bit RSA signature */ #undef CONFIG_RSA /* Define the RSA key size. */ #undef CONFIG_RSA_KEY_SIZE /* Use RSA exponent 3 instead of F4 (65537) */ #undef CONFIG_RSA_EXPONENT_3 /* * Adjust the compiler optimization flags for the RSA code to get a speed-up * at the expense of a small code size delta. */ #undef CONFIG_RSA_OPTIMIZED /* * Verify the RW firmware using the RSA signature. * (for accessories without software sync) */ #undef CONFIG_RWSIG /* * Disable rwsig jump when the reset source is hard pin-reset. This only work * for the case where rwsig task is not used. */ #undef CONFIG_RWSIG_DONT_CHECK_ON_PIN_RESET /* * When RWSIG verification is performed as a task, time to wait from signature * verification to an automatic jump to RW (if AP does not request the wait to * be interrupted). */ #define CONFIG_RWSIG_JUMP_TIMEOUT (1000 * MSEC) /* * Defines what type of futility signature type should be used. * RWSIG should be used for new designs. * Old adapters use the USBPD1 futility signature type. */ #undef CONFIG_RWSIG_TYPE_RWSIG #undef CONFIG_RWSIG_TYPE_USBPD1 /* * By default the pubkey and sig are put at the end of the first and second * half of the total flash, and take up the minimum space possible. You can * override those defaults with these. */ #undef CONFIG_RO_PUBKEY_ADDR #undef CONFIG_RO_PUBKEY_SIZE #undef CONFIG_RW_SIG_ADDR #undef CONFIG_RW_SIG_SIZE /* Size of the serial number if needed */ #undef CONFIG_SERIALNO_LEN /****************************************************************************/ /* Shared objects library. */ /* Support shared objects library between RO and RW. */ #undef CONFIG_SHAREDLIB /* Size of shared objects library. */ #undef CONFIG_SHAREDLIB_SIZE /* Program memory offset of shared objects library. */ #undef CONFIG_SHAREDLIB_MEM_OFF /* Storage offset of sharedobjects library. */ #undef CONFIG_SHAREDLIB_STORAGE_OFF /* * If defined, the hash module will save its last computed hash when jumping * between EC images. */ #undef CONFIG_SAVE_VBOOT_HASH /* Allow the board to use a GPIO for the SCI# signal. */ #undef CONFIG_SCI_GPIO /* Support computing SHA-1 hash */ #undef CONFIG_SHA1 /* Support computing of other hash sizes (without the VBOOT code) */ #undef CONFIG_SHA256 /* Unroll some loops in SHA256_transform for better performance. */ #undef CONFIG_SHA256_UNROLLED /* Emulate the CLZ (Count Leading Zeros) in software for CPU lacking support */ #undef CONFIG_SOFTWARE_CLZ /* Emulate the CLZ (Count Trailing Zeros) in software for CPU lacking support */ #undef CONFIG_SOFTWARE_CTZ /* Support smbus interface */ #undef CONFIG_SMBUS /* Support SPI interfaces */ #undef CONFIG_SPI /* Support deprecated SPI protocol version 2. */ #undef CONFIG_SPI_PROTOCOL_V2 /* * Support SPI Slave interfaces. The first board supporting this is cr50 and * in its parlance SPI_SLAVE is called SPS. This convention might be * reconsidered later, and the use of "SPI" in different config options needs * to be cleand up. (crbug.com/512613). */ #undef CONFIG_SPS /* Define the SPI port to use to access SPI accelerometer */ #undef CONFIG_SPI_ACCEL_PORT /* Support SPI flash */ #undef CONFIG_SPI_FLASH /* Support SPI flash protection register translation */ #undef CONFIG_SPI_FLASH_REGS /* Define the SPI port to use to access the flash */ #undef CONFIG_SPI_FLASH_PORT /* Select any of the following SPI flash configs that your board uses. */ #undef CONFIG_SPI_FLASH_GD25LQ40 #undef CONFIG_SPI_FLASH_GD25Q41B #undef CONFIG_SPI_FLASH_W25Q128 #undef CONFIG_SPI_FLASH_W25Q40 #undef CONFIG_SPI_FLASH_W25Q64 #undef CONFIG_SPI_FLASH_W25Q80 #undef CONFIG_SPI_FLASH_W25X40 /* SPI flash part supports SR2 register */ #undef CONFIG_SPI_FLASH_HAS_SR2 /* Define the SPI port to use to access the fingerprint sensor */ #undef CONFIG_SPI_FP_PORT /* Support JEDEC SFDP based Serial NOR flash */ #undef CONFIG_SPI_NOR /* Enable SPI_NOR debugging providing additional console output while * initializing Serial NOR Flash devices including SFDP discovery. */ #undef CONFIG_SPI_NOR_DEBUG /* Maximum Serial NOR flash command size, in Bytes */ #undef CONFIG_SPI_NOR_MAX_MESSAGE_SIZE /* Maximum Serial NOR flash read size, in Bytes */ #undef CONFIG_SPI_NOR_MAX_READ_SIZE /* Maximum Serial NOR flash write size, in Bytes. Note this must be a power of * two. */ #undef CONFIG_SPI_NOR_MAX_WRITE_SIZE /* If defined will enable block (64KiB) erase operations. */ #undef CONFIG_SPI_NOR_BLOCK_ERASE /* If defined will read the sector/block to be erased first and only initiate * the erase operation if not already in an erased state. The read operation * (performed in CONFIG_SPI_NOR_MAX_READ_SIZE chunks) is aborted early if a * non "0xff" byte is encountered. * !! Make sure there is enough stack space to host a * !! CONFIG_SPI_NOR_MAX_READ_SIZE sized buffer before enabling. */ #undef CONFIG_SPI_NOR_SMART_ERASE /* SPI master feature */ #undef CONFIG_SPI_MASTER /* SPI master halfduplex/3-wire mode */ #undef CONFIG_SPI_HALFDUPLEX /* Support STM32 SPI1 as master. */ #undef CONFIG_STM32_SPI1_MASTER /* SPI master configure gpios on init */ #undef CONFIG_SPI_MASTER_CONFIGURE_GPIOS /* Support SPI masters without GPIO-specified Chip Selects, instead rely on the * SPI master port's hardwired CS pin. */ #undef CONFIG_SPI_MASTER_NO_CS_GPIOS /* Support MCHP MEC family GP-SPI master(s) * Define to 0x01 for GPSPI0 only. * Define to 0x02 for GPSPI1 only. * Define to 0x03 for both controllers. */ #undef CONFIG_MCHP_GPSPI /* Support testing SPI slave controller driver. */ #undef CONFIG_SPS_TEST /* Default stack size to use for tasks, in bytes */ #undef CONFIG_STACK_SIZE /* Use 32-bit timer for clock source on stm32. */ #undef CONFIG_STM_HWTIMER32 /* Compile charger detect for STM32 */ #undef CONFIG_STM32_CHARGER_DETECT /* Fake hibernate mode */ #undef CONFIG_STM32L_FAKE_HIBERNATE /* * Compile common code to handle simple switch inputs such as the recovery * button input from the servo debug interface. */ #undef CONFIG_SWITCH /* Support dedicated recovery signal from servo board */ #undef CONFIG_SWITCH_DEDICATED_RECOVERY /* * System should remain unlocked even if write protect is enabled. * * NOTE: This should ONLY be defined during bringup, and should never be * defined on a shipping / released platform. */ #undef CONFIG_SYSTEM_UNLOCKED /* * Device can be a tablet as well as a clamshell. */ #undef CONFIG_TABLET_MODE /* * Add a virtual switch to indicate when we are in tablet mode. */ #undef CONFIG_TABLET_MODE_SWITCH /* * Microchip Trace FIFO Debug Port */ #undef CONFIG_MCHP_TFDP /*****************************************************************************/ /* Task config */ /* * List of enabled tasks in ascending priority order. This is normally * defined in each board's ec.tasklist file. * * For each task, use the macro TASK_ALWAYS(n, r, d, s) for base tasks and * TASK_NOTEST(n, r, d, s) for tasks that can be excluded in test binaries, * where : * 'n' is the name of the task * 'r' is the main routine of the task * 'd' is an opaque parameter passed to the routine at startup * 's' is the stack size in bytes; must be a multiple of 8 */ #undef CONFIG_TASK_LIST /* * List of test tasks. Same format as CONFIG_TASK_LIST, but used to define * additional tasks for a unit test. Normally defined in * test/{testname}.tasklist. */ #undef CONFIG_TEST_TASK_LIST /* * List of tasks used by CTS * * cts.tasklist contains tasks run only for CTS. These tasks are added to the * tasks registered in ec.tasklist with higher priority. * * If a CTS suite does not define its own cts.tasklist, the common list is used * (i.e. cts/cts.tasklist). */ #undef CONFIG_CTS_TASK_LIST /* * Enable task profiling. * * Boards may #undef this to reduce image size and RAM usage. */ #define CONFIG_TASK_PROFILING /*****************************************************************************/ /* Temperature sensor config */ /* Compile common code for temperature sensor support */ #undef CONFIG_TEMP_SENSOR /* Support particular temperature sensor chips */ #undef CONFIG_TEMP_SENSOR_ADT7481 /* ADT 7481 sensor, on I2C bus */ #undef CONFIG_TEMP_SENSOR_BD99992GW /* BD99992GW PMIC, on I2C bus */ #undef CONFIG_TEMP_SENSOR_EC_ADC /* Thermistors on EC's own ADC */ #undef CONFIG_TEMP_SENSOR_G781 /* G781 sensor, on I2C bus */ #undef CONFIG_TEMP_SENSOR_G782 /* G782 sensor, on I2C bus */ #undef CONFIG_TEMP_SENSOR_SB_TSI /* SB_TSI sensor, on I2C bus */ #undef CONFIG_TEMP_SENSOR_TMP006 /* TI TMP006 sensor, on I2C bus */ #undef CONFIG_TEMP_SENSOR_TMP411 /* TI TMP411 sensor, on I2C bus */ #undef CONFIG_TEMP_SENSOR_TMP432 /* TI TMP432 sensor, on I2C bus */ #undef CONFIG_TEMP_SENSOR_F75303 /* Fintek F75303 sensor, on I2C bus */ #undef CONFIG_THERMISTOR_NCP15WB /* NCP15WB thermistor */ /* * If defined, active-high GPIO which indicates temperature sensor chips are * powered. If not defined, temperature sensors are assumed to be always * powered. */ #undef CONFIG_TEMP_SENSOR_POWER_GPIO /* Compile common code for throttling the CPU based on the temp sensors */ #undef CONFIG_THROTTLE_AP /* * If defined, dptf is enabled to manage thermals. * * NOTE: This doesn't mean that thermal control is completely taken care by * DPTF. We have some hybrid solutions where the EC still manages the fans. */ #undef CONFIG_DPTF /*****************************************************************************/ /* Touchpad config */ /* Enable touchpad, you must pick a driver (currently, only Elan exists) */ #undef CONFIG_TOUCHPAD /* Enable Elan driver */ #undef CONFIG_TOUCHPAD_ELAN /* Set I2C port and address (8-bit) */ #undef CONFIG_TOUCHPAD_I2C_PORT #undef CONFIG_TOUCHPAD_I2C_ADDR /* * Enable touchpad FW update over USB update protocol, and define touchpad * virtual address and size. */ #undef CONFIG_TOUCHPAD_VIRTUAL_OFF #undef CONFIG_TOUCHPAD_VIRTUAL_SIZE /* * Include hashes of the touchpad FW in the EC image, passed as TOUCHPAD_FW * parameter to make command. */ #undef CONFIG_TOUCHPAD_HASH_FW /*****************************************************************************/ /* TPM-like configuration */ /* Speak the TPM SPI Hardware Protocol on the SPI slave interface */ #undef CONFIG_TPM_SPS /* Speak to the TPM 2.0 hardware protocol on the I2C slave interface */ #undef CONFIG_TPM_I2CS /* Record TPM events in circular buffer */ #undef CONFIG_TPM_LOGGING /*****************************************************************************/ /* USART stream config */ #undef CONFIG_STREAM_USART /* * Each USART stream can be individually enabled and accessible using the * stream interface provided in the usart_config struct. */ #undef CONFIG_STREAM_USART1 #undef CONFIG_STREAM_USART2 #undef CONFIG_STREAM_USART3 #undef CONFIG_STREAM_USART4 /*****************************************************************************/ /* U2F config: second factor authentication */ #undef CONFIG_U2F /*****************************************************************************/ /* USB stream config */ #undef CONFIG_STREAM_USB /*****************************************************************************/ /* UART config */ /* Baud rate for UARTs */ #define CONFIG_UART_BAUD_RATE 115200 /* Allow bit banging of a UARTs pins and bypassing the UART block. */ #undef CONFIG_UART_BITBANG /* UART index (number) for EC console */ #undef CONFIG_UART_CONSOLE /* UART index (number) for host UART, if present */ #undef CONFIG_UART_HOST /* Use uart_input_filter() to filter UART input. See prototype in uart.h */ #undef CONFIG_UART_INPUT_FILTER /* * Allow switching the EC console UART to an alternate pad. This must be * used for short transactions only, and EC is only able to receive data on * that alternate pad after it has been explicitly switched. */ #undef CONFIG_UART_PAD_SWITCH /* * UART receive buffer size in bytes. Must be a power of 2 for macros in * common/uart_buffering.c to work properly. Must be larger than * CONFIG_CONSOLE_INPUT_LINE_SIZE to copy and paste scripts. */ #define CONFIG_UART_RX_BUF_SIZE 128 /* Use DMA for UART input */ #undef CONFIG_UART_RX_DMA /* * On some platforms, UART receive DMA can't trigger an interrupt when a single * character is received. Those platforms poll for characters every HOOK_TICK. * When a character is received, make this many additional checks between then * and the next HOOK_TICK, to increase responsiveness of the console to input. */ #define CONFIG_UART_RX_DMA_RECHECKS 5 /* * UART transmit buffer size in bytes. Must be a power of 2 for macros in * common/uart_buffering.c to work properly. */ #define CONFIG_UART_TX_BUF_SIZE 512 /* Use DMA for UART output */ #undef CONFIG_UART_TX_DMA /* The DMA channel for UART. If not defined, default to UART1. */ #undef CONFIG_UART_TX_DMA_CH #undef CONFIG_UART_RX_DMA_CH /* The DMA peripheral request signal for UART TX. STM32 only. */ #undef CONFIG_UART_TX_DMA_PH /* The DMA channel mapping config for stm32f4. */ #undef CONFIG_UART_TX_REQ_CH #undef CONFIG_UART_RX_REQ_CH /*****************************************************************************/ /* USB PD config */ /* Include all USB Power Delivery modules */ #undef CONFIG_USB_POWER_DELIVERY /* Support for USB PD alternate mode */ #undef CONFIG_USB_PD_ALT_MODE /* Support for USB PD alternate mode of Downward Facing Port */ #undef CONFIG_USB_PD_ALT_MODE_DFP /* Check if max voltage request is allowed before each request */ #undef CONFIG_USB_PD_CHECK_MAX_REQUEST_ALLOWED /* Default state of PD communication disabled flag */ #undef CONFIG_USB_PD_COMM_DISABLED /* * Do not enable PD communication in RO as a security measure. * We don't want to allow communication to outside world until * we jump to RW. This can by overridden with the removal of * the write protect screw to allow for easier testing. */ #undef CONFIG_USB_PD_COMM_LOCKED /* Respond to custom vendor-defined messages over PD */ #undef CONFIG_USB_PD_CUSTOM_VDM /* Default USB data role when a USB PD debug accessory is seen */ #define CONFIG_USB_PD_DEBUG_DR PD_ROLE_DFP /* * Define to have a fixed PD Task debug level. * Undef to allow runtime change via console command. */ #undef CONFIG_USB_PD_DEBUG_LEVEL /* * Define if this board can enable VBUS discharge (eg. through a GPIO-controlled * discharge circuit, or through port controller registers) to discharge VBUS * rapidly on disconnect. Will be defined automatically when one of the below * options is defined. */ #undef CONFIG_USB_PD_DISCHARGE /* Define if discharge circuit is EC GPIO-controlled. */ #undef CONFIG_USB_PD_DISCHARGE_GPIO /* Define if discharge circuit is using PD discharge registers on TCPC. */ #undef CONFIG_USB_PD_DISCHARGE_TCPC /* Define if discharge circuit is using PD discharge registers on PPC. */ #undef CONFIG_USB_PD_DISCHARGE_PPC /* Define if this board can act as a dual-role PD port (source and sink) */ #undef CONFIG_USB_PD_DUAL_ROLE /* Define if this board can used TCPC-controlled DRP toggle */ #undef CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE /* Initial DRP / toggle policy */ #define CONFIG_USB_PD_INITIAL_DRP_STATE PD_DRP_TOGGLE_OFF /* * Define if VBUS source GPIOs (GPIO_USB_C*_5V_EN) are active-low (and named * (..._L) rather than default active-high. */ #undef CONFIG_USB_PD_5V_EN_ACTIVE_LOW /* Ask charger if VBUS is enabled on a source port, instead of using GPIO */ #undef CONFIG_USB_PD_5V_CHARGER_CTRL /* Dynamic USB PD source capability */ #undef CONFIG_USB_PD_DYNAMIC_SRC_CAP /* Support USB PD flash. */ #undef CONFIG_USB_PD_FLASH /* Check whether PD is the sole power source before flash erase operation */ #undef CONFIG_USB_PD_FLASH_ERASE_CHECK /* Define if this board, operating as a sink, can give power back to a source */ #undef CONFIG_USB_PD_GIVE_BACK /* Enable USB PD Rev3.0 features */ #undef CONFIG_USB_PD_REV30 /* Major and Minor ChromeOS specific PD device Hardware IDs. */ #undef CONFIG_USB_PD_HW_DEV_ID_BOARD_MAJOR #undef CONFIG_USB_PD_HW_DEV_ID_BOARD_MINOR /* HW & SW version for alternate mode discover identity response (4bits each) */ #undef CONFIG_USB_PD_IDENTITY_HW_VERS #undef CONFIG_USB_PD_IDENTITY_SW_VERS /* USB PD MCU slave address for host commands */ #define CONFIG_USB_PD_I2C_SLAVE_ADDR 0x3c /* Define if using internal comparator for PD receive */ #undef CONFIG_USB_PD_INTERNAL_COMP /* Record main PD events in a circular buffer */ #undef CONFIG_USB_PD_LOGGING /* The size in bytes of the FIFO used for event logging */ #define CONFIG_EVENT_LOG_SIZE 512 /* Save power by waking up on VBUS rather than polling CC */ #define CONFIG_USB_PD_LOW_POWER /* Allow chip to go into low power idle even when a PD device is attached */ #undef CONFIG_USB_PD_LOW_POWER_IDLE_WHEN_CONNECTED /* Number of USB PD ports */ #undef CONFIG_USB_PD_PORT_COUNT /* Simple DFP, such as power adapter, will not send discovery VDM on connect */ #undef CONFIG_USB_PD_SIMPLE_DFP /* Use comparator module for PD RX interrupt */ #define CONFIG_USB_PD_RX_COMP_IRQ /* Use TCPC module (type-C port controller) */ #undef CONFIG_USB_PD_TCPC /* Enable TCPC to enter low power mode */ #undef CONFIG_USB_PD_TCPC_LOW_POWER /* * Track VBUS level in TCPC module. This will only be needed if we're acting * as an external TCPC. */ #undef CONFIG_USB_PD_TCPC_TRACK_VBUS /* * Choose one of the following TCPMs (type-C port manager) to manage TCPC. The * TCPM stub is used to make direct function calls to TCPC when TCPC is on * the same MCU. The TCPCI TCPM uses the standard TCPCI i2c interface to TCPC. */ #undef CONFIG_USB_PD_TCPM_STUB #undef CONFIG_USB_PD_TCPM_TCPCI #undef CONFIG_USB_PD_TCPM_FUSB302 #undef CONFIG_USB_PD_TCPM_ITE83XX #undef CONFIG_USB_PD_TCPM_ANX3429 #undef CONFIG_USB_PD_TCPM_ANX740X #undef CONFIG_USB_PD_TCPM_ANX741X #undef CONFIG_USB_PD_TCPM_ANX7688 #undef CONFIG_USB_PD_TCPM_PS8751 #undef CONFIG_USB_PD_TCPM_PS8805 /* * Use this option if the TCPC port controller supports the optional register * 18h CONFIG_STANDARD_OUTPUT to steer the high-speed muxes. */ #undef CONFIG_USB_PD_TCPM_MUX /* * The TCPM must know whether VBUS is present in order to make proper state * transitions. In addition, charge_manager must know about VBUS presence in * order to make charging decisions. VBUS state can be determined by various * methods: * - Some TCPCs can detect and report the presence of VBUS. * - In some configurations, charger ICs can report the presence of VBUS. * - On some boards, dedicated VBUS interrupt pins are available. * - Some power path controllers (PPC) can report the presence of VBUS. * * Exactly one of these should be defined for all boards that run the PD * state machine. */ #undef CONFIG_USB_PD_VBUS_DETECT_TCPC #undef CONFIG_USB_PD_VBUS_DETECT_CHARGER #undef CONFIG_USB_PD_VBUS_DETECT_GPIO #undef CONFIG_USB_PD_VBUS_DETECT_PPC #undef CONFIG_USB_PD_VBUS_DETECT_NONE /* Define if the there is a separate ADC channel for each USB-C Vbus voltage */ #undef CONFIG_USB_PD_VBUS_MEASURE_ADC_EACH_PORT /* Define if the there is no hardware to measure Vbus voltage */ #undef CONFIG_USB_PD_VBUS_MEASURE_NOT_PRESENT /* Define the type-c port controller I2C base address. */ #define CONFIG_TCPC_I2C_BASE_ADDR 0x9c /* Use this option to enable Try.SRC mode for Dual Role devices */ #undef CONFIG_USB_PD_TRY_SRC /* Set the default minimum battery percentage for Try.Src to be enabled */ #define CONFIG_USB_PD_TRY_SRC_MIN_BATT_SOC 1 /* Alternative configuration keeping only the TX part of PHY */ #undef CONFIG_USB_PD_TX_PHY_ONLY /* Use DAC as reference for comparator at 850mV. */ #undef CONFIG_PD_USE_DAC_AS_REF /* USB Product ID. */ #undef CONFIG_USB_PID /* PPC needs to be informed of CC polarity */ #undef CONFIG_USBC_PPC_POLARITY /* USB Type-C Power Path Controllers (PPC) */ #undef CONFIG_USBC_PPC_NX20P3483 #undef CONFIG_USBC_PPC_SN5S330 /* PPC is capable of providing VCONN */ #undef CONFIG_USBC_PPC_VCONN /* Support for USB type-c superspeed mux */ #undef CONFIG_USBC_SS_MUX /* * Only configure USB type-c superspeed mux when DFP (for chipsets that * don't support being a UFP) */ #undef CONFIG_USBC_SS_MUX_DFP_ONLY /* Support v1.1 type-C connection state machine */ #undef CONFIG_USBC_BACKWARDS_COMPATIBLE_DFP /* Support for USB type-c vconn. Not needed for captive cables. */ #undef CONFIG_USBC_VCONN /* Support VCONN swap */ #undef CONFIG_USBC_VCONN_SWAP /* USB Binary device Object Store support */ #undef CONFIG_USB_BOS /* USB Device version of product */ #undef CONFIG_USB_BCD_DEV /* * Used during generation of VIF for USB Type-C Compliance Testing. * Indicates whether the UUT can communicate with USB 2.0 or USB 3.1 as a host * or as the Downstream Facing Port of a hub. */ #undef CONFIG_VIF_TYPE_C_CAN_ACT_AS_HOST /* * Used during generation of VIF for USB Type-C Compliance Testing. * Indicates whether the UUT has a captive cable. */ #undef CONFIG_VIF_CAPTIVE_CABLE /*****************************************************************************/ /* Compile chip support for the USB device controller */ #undef CONFIG_USB /* Support USB isochronous handler */ #undef CONFIG_USB_ISOCHRONOUS /* Support USB blob handler. */ #undef CONFIG_USB_BLOB /* Common USB / BC1.2 charger detection routines */ #undef CONFIG_USB_CHARGER /* External BC1.2 charger detection devices. */ #undef CONFIG_BC12_DETECT_BQ24392 #undef CONFIG_BC12_DETECT_PI3USB9281 /* Number of Pericom PI3USB9281 chips present in system */ #undef CONFIG_BC12_DETECT_PI3USB9281_CHIP_COUNT /* Enable USB serial console module. */ #undef CONFIG_USB_CONSOLE /* * Enable USB serial console crc32 computation. * Also makes console output block on overrun. */ #undef CONFIG_USB_CONSOLE_CRC /* Support USB HID interface. */ #undef CONFIG_USB_HID /* Support USB HID keyboard interface. */ #undef CONFIG_USB_HID_KEYBOARD /* Support USB HID keyboard backlight. */ #undef CONFIG_USB_HID_KEYBOARD_BACKLIGHT /* Support USB HID touchpad interface. */ #undef CONFIG_USB_HID_TOUCHPAD /* HID touchpad logical dimensions */ #undef CONFIG_USB_HID_TOUCHPAD_LOGICAL_MAX_X #undef CONFIG_USB_HID_TOUCHPAD_LOGICAL_MAX_Y /* HID touchpad physical dimensions (tenth of mm) */ #undef CONFIG_USB_HID_TOUCHPAD_PHYSICAL_MAX_X #undef CONFIG_USB_HID_TOUCHPAD_PHYSICAL_MAX_Y /* USB device buffers and descriptors */ #undef CONFIG_USB_RAM_ACCESS_SIZE #undef CONFIG_USB_RAM_ACCESS_TYPE #undef CONFIG_USB_RAM_BASE #undef CONFIG_USB_RAM_SIZE /* Disable automatic connection of USB peripheral */ #undef CONFIG_USB_INHIBIT_CONNECT /* Disable automatic initialization of USB peripheral */ #undef CONFIG_USB_INHIBIT_INIT /* Support control of multiple PHY */ #undef CONFIG_USB_SELECT_PHY /* Select which USB PHY will be used at startup */ #undef CONFIG_USB_SELECT_PHY_DEFAULT /* Support simple control of power to the device's USB ports */ #undef CONFIG_USB_PORT_POWER_DUMB /* * Support supplying USB power in S3, if the host leaves the port enabled when * entering S3. */ #undef CONFIG_USB_PORT_POWER_IN_S3 /* * Support smart power control to the device's USB ports, using * dedicated power control chips. This potentially enables automatic * negotiation of supplying more power to peripherals. */ #undef CONFIG_USB_PORT_POWER_SMART /* * Support smart power control to the device's USB ports, however only CDP and * SDP are supported. Usually this is the case if all the control lines to the * charging port controller are hard-wired. */ #undef CONFIG_USB_PORT_POWER_SMART_CDP_SDP_ONLY /* * Override the default charging mode for USB smart power control. * Value is selected from usb_charge_mode in include/usb_charge.h */ #undef CONFIG_USB_PORT_POWER_SMART_DEFAULT_MODE /* * Smart USB power control can use a full set of control signals to the USB * port power chip, or a reduced set. If this is defined, use the reduced set. */ #undef CONFIG_USB_PORT_POWER_SMART_SIMPLE /* Number of smart USB power ports. */ #define CONFIG_USB_PORT_POWER_SMART_PORT_COUNT 2 /* * Smart USB power control current limit pins may be inverted. In this case * they are active low and the GPIO names will be GPIO_USBn_ILIM_SEL_L. */ #undef CONFIG_USB_PORT_POWER_SMART_INVERTED /* * Support waking up host by setting the K-state on the data lines (requires * CONFIG_USB_SUSPEND to be set as well). */ #undef CONFIG_USB_REMOTE_WAKEUP /* Support programmable USB device iSerial field. */ #undef CONFIG_USB_SERIALNO /* Support reporting of configuration bMaxPower in mA */ #define CONFIG_USB_MAXPOWER_MA 500 /* Support reporting as self powered in USB configuration. */ #undef CONFIG_USB_SELF_POWERED /* Support correct handling of USB suspend (host-initiated). */ #undef CONFIG_USB_SUSPEND /* Default pull-up value on the USB-C ports when they are used as source. */ #define CONFIG_USB_PD_PULLUP TYPEC_RP_1A5 /* * Override the pull-up value when only zero or one port is actively sourcing * current and we can advertise more current than what is defined by * `CONFIG_USB_PD_PULLUP`. * Should be defined with one of the tcpc_rp_value. */ #undef CONFIG_USB_PD_MAX_SINGLE_SOURCE_CURRENT /******************************************************************************/ /* stm32f4 dwc usb configs. */ /* Set USB speed to FS rather than HS */ #undef CONFIG_USB_DWC_FS /******************************************************************************/ /* USB port switch */ /* Support the ITE IT5205 Type-C USB alternate mode mux. */ #undef CONFIG_USB_MUX_IT5205 /* Support the Pericom PI3USB30532 USB3.0/DP1.2 Matrix Switch */ #undef CONFIG_USB_MUX_PI3USB30532 /* Support the Parade PS8740 Type-C Redriving Switch */ #undef CONFIG_USB_MUX_PS8740 /* Support the Parade PS8743 Type-C Redriving Switch */ #undef CONFIG_USB_MUX_PS8743 /* 'Virtual' USB mux under host (not EC) control */ #undef CONFIG_USB_MUX_VIRTUAL /*****************************************************************************/ /* USB GPIO config */ #undef CONFIG_USB_GPIO /*****************************************************************************/ /* USB SPI config */ #undef CONFIG_USB_SPI /*****************************************************************************/ /* USB I2C config */ #undef CONFIG_USB_I2C /* Allowed read/write count for USB over I2C */ #define CONFIG_USB_I2C_MAX_WRITE_COUNT 60 #define CONFIG_USB_I2C_MAX_READ_COUNT 60 /*****************************************************************************/ /* USB Power monitoring interface config */ #undef CONFIG_USB_POWER /*****************************************************************************/ /* * USB stream signing config. This allows data read over UART or SPI * to have a signature generated that can be used to validate the data * offline based on H1's registered key. Used by mn50. */ #undef CONFIG_STREAM_SIGNATURE /*****************************************************************************/ /* Support early firmware selection */ #undef CONFIG_VBOOT_EFS /* Support computing hash of code for verified boot */ #undef CONFIG_VBOOT_HASH /* Support for secure temporary storage for verified boot */ #undef CONFIG_VSTORE /* Number of supported slots for secure temporary storage */ #undef CONFIG_VSTORE_SLOT_COUNT /*****************************************************************************/ /* Watchdog config */ /* * Compile watchdog timer support. The watchdog timer will reboot the system * if the hook task (which is the lowest-priority task on the system) gets * starved for CPU time and isn't able to fire its HOOK_TICK event. */ #define CONFIG_WATCHDOG /* * Try to detect a watchdog that is about to fire, and print a trace. This is * required on chips such as STM32 where the watchdog timer simply reboots the * system without any early warning. */ #undef CONFIG_WATCHDOG_HELP /* Watchdog period in ms; see also AUX_TIMER_PERIOD_MS */ #define CONFIG_WATCHDOG_PERIOD_MS 1600 /* * Fire auxiliary timer 500ms before watchdog timer expires. This leaves * some time for debug trace to be printed. */ #define CONFIG_AUX_TIMER_PERIOD_MS (CONFIG_WATCHDOG_PERIOD_MS - 500) /*****************************************************************************/ /* WebUSB config */ /* * Enable the WebUSB support and define its URL. * Export a WebUSB Platform Descriptor in the Binary Object Store descriptor. * The WebUSB landing page URL is equal to 'CONFIG_WEBUSB_URL' plus the * https:// prefix. * This requires CONFIG_USB_BOS. */ #undef CONFIG_WEBUSB_URL /*****************************************************************************/ /* * Support controlling power to WiFi, WWAN (3G/LTE), and/or bluetooth modules. */ #undef CONFIG_WIRELESS /* * Support for WiFi devices that must remain powered in suspend. Set to the * combination of EC_WIRELESS_SWITCH flags (from ec_commands.h) which should * be set in suspend. */ #undef CONFIG_WIRELESS_SUSPEND /* WiFi power control signal is active-low. */ #undef CONFIG_WLAN_POWER_ACTIVE_LOW /* Support Wake-on-Voice */ #undef CONFIG_WAKE_ON_VOICE /* * Write protect signal is active-high. If this is defined, there must be a * GPIO named GPIO_WP; if not defined, there must be a GPIO names GPIO_WP_L. */ #undef CONFIG_WP_ACTIVE_HIGH /* * The write protect signal is always asserted, * independantly of the GPIO existence or current value. */ #undef CONFIG_WP_ALWAYS /* * If needed to allocate some free space in the base of the RO or RW section * of the image, define these to be equal the required size of the free space. */ #undef CONFIG_RO_HEAD_ROOM #undef CONFIG_RW_HEAD_ROOM /* Firmware upgrade options. */ /* Firmware updates using other than HC channel(s). */ #undef CONFIG_NON_HC_FW_UPDATE #undef CONFIG_USB_FW_UPDATE /* A different config for the same update. TODO(vbendeb): dedup these */ #undef CONFIG_USB_UPDATE /* Add support for pairing over the USB update interface. */ #undef CONFIG_USB_PAIRING /* PDU size for fw update over USB (or TPM). */ #define CONFIG_UPDATE_PDU_SIZE 1024 /* * If defined, charge_get_state returns a special status if battery is * discharging and battery is nearly full. */ #undef CONFIG_PWR_STATE_DISCHARGE_FULL /* * Define this if a chip needs to add some information to the common 'version' * command output. */ #undef CONFIG_EXTENDED_VERSION_INFO /* * Define this if board ID support is required. For g chip based boards it * allows to nail different images to different boards. */ #undef CONFIG_BOARD_ID_SUPPORT /* * Define this to enable Cros Board Info support. I2C_EEPROM_PORT and * I2C_EEPROM_ADDR must be defined as well. */ #undef CONFIG_CROS_BOARD_INFO /*****************************************************************************/ /* * Include board and core configs, since those hold the CONFIG_ constants for a * given configuration. This guarantees they get included everywhere, and * fixes a fairly common bug where we gate out code with #ifndef * CONFIG_SOMETHING and but forget to include both of these. * * Board is included after chip, so that chip defaults can be overridden on a * per-board basis as needed. */ #ifdef __CROS_EC_CONFIG_CHIP_H #error Include config.h instead of config_chip.h! #endif #ifdef __BOARD_H #error Include config.h instead of board.h! #endif #include "config_chip.h" #ifdef HAS_BASEBOARD #include "baseboard.h" #endif #include "board.h" /******************************************************************************/ /* * Set default data ram size unless it's customized by the chip. */ #ifndef CONFIG_DATA_RAM_SIZE #define CONFIG_DATA_RAM_SIZE CONFIG_RAM_SIZE #endif /******************************************************************************/ /* * Disable the built-in console history if using the experimental console. * * The experimental console keeps its own session-persistent history which * survives EC reboot. It also requires CRC8 for command integrity. */ #ifdef CONFIG_EXPERIMENTAL_CONSOLE #undef CONFIG_CONSOLE_HISTORY #define CONFIG_CRC8 #endif /* defined(CONFIG_EXPERIMENTAL_CONSOLE) */ /******************************************************************************/ /* * Throttle AP must have temperature sensor enabled to get the readings for * thermal throttling. */ #if defined(CONFIG_THROTTLE_AP) && !defined(CONFIG_TEMP_SENSOR) #define CONFIG_TEMP_SENSOR #endif /******************************************************************************/ /* * DPTF must have temperature sensor enabled to get the readings for * generating DPTF thresholds events. */ #if defined(CONFIG_DPTF) && !defined(CONFIG_TEMP_SENSOR) #define CONFIG_TEMP_SENSOR #endif /******************************************************************************/ /* The Matrix Keyboard Protocol depends on MKBP events. */ #ifdef CONFIG_KEYBOARD_PROTOCOL_MKBP #define CONFIG_MKBP_EVENT #endif /******************************************************************************/ /* Set generic orientation config if a specific orientation config is set. */ #if defined(CONFIG_KX022_ORIENTATION_SENSOR) || \ defined(CONFIG_BMI160_ORIENTATION_SENSOR) #ifndef CONFIG_ACCEL_FIFO #error CONFIG_ACCEL_FIFO must be defined to use hw orientation sensor support #endif #define CONFIG_ORIENTATION_SENSOR #endif /*****************************************************************************/ /* Define CONFIG_BATTERY if board has a battery. */ #if defined(CONFIG_BATTERY_BQ20Z453) || \ defined(CONFIG_BATTERY_BQ27541) || \ defined(CONFIG_BATTERY_BQ27621) || \ defined(CONFIG_BATTERY_MAX17055) || \ defined(CONFIG_BATTERY_SMART) #define CONFIG_BATTERY #endif /*****************************************************************************/ /* Define CONFIG_USBC_PPC if board has a USB Type-C Power Path Controller. */ #if defined(CONFIG_USBC_PPC_SN5S330) || defined(CONFIG_USBC_PPC_NX20P3483) #define CONFIG_USBC_PPC #endif /* "has a PPC" */ /* The TI SN5S330 supports VCONN and needs to be informed of CC polarity */ #if defined(CONFIG_USBC_PPC_SN5S330) #define CONFIG_USBC_PPC_POLARITY #define CONFIG_USBC_PPC_VCONN #endif /*****************************************************************************/ /* * Define CONFIG_USB_PD_VBUS_MEASURE_CHARGER if the charger on the board * supports VBUS measurement. */ #if defined(CONFIG_CHARGER_BD9995X) || \ defined(CONFIG_CHARGER_RT9466) || \ defined(CONFIG_CHARGER_RT9467) #define CONFIG_USB_PD_VBUS_MEASURE_CHARGER #endif /*****************************************************************************/ /* * Define CONFIG_CHARGER_NARROW_VDC for chargers that use a Narrow VDC power * architecture. */ #if defined(CONFIG_CHARGER_ISL9237) || defined(CONFIG_CHARGER_ISL9238) #define CONFIG_CHARGER_NARROW_VDC #endif /*****************************************************************************/ /* * Define CONFIG_BUTTON_TRIGGERED_RECOVERY if a board has a dedicated recovery * button. */ #ifdef CONFIG_DEDICATED_RECOVERY_BUTTON #define CONFIG_BUTTON_TRIGGERED_RECOVERY #endif /* defined(CONFIG_DEDICATED_RECOVERY_BUTTON) */ #ifdef CONFIG_LED_PWM_COUNT #define CONFIG_LED_PWM #endif /* defined(CONFIG_LED_PWM_COUNT) */ /*****************************************************************************/ /* * Define derived configuration options for EC-EC communication */ #ifdef CONFIG_EC_EC_COMM_BATTERY #ifdef CONFIG_EC_EC_COMM_MASTER #define CONFIG_EC_EC_COMM_BATTERY_MASTER #define CONFIG_BATTERY_V2 #define CONFIG_BATTERY_COUNT 2 #endif #ifdef CONFIG_EC_EC_COMM_SLAVE #define CONFIG_EC_EC_COMM_BATTERY_SLAVE #define CONFIG_BATTERY_V2 #define CONFIG_BATTERY_COUNT 1 #endif #endif /* CONFIG_EC_EC_COMM_BATTERY */ /*****************************************************************************/ /* Define derived USB PD Discharge common path */ #if defined(CONFIG_USB_PD_DISCHARGE_GPIO) || \ defined(CONFIG_USB_PD_DISCHARGE_TCPC) || \ defined(CONFIG_USB_PD_DISCHARGE_PPC) #define CONFIG_USB_PD_DISCHARGE #endif /*****************************************************************************/ /* * Handle task-dependent configs. * * This prevent sub-modules from being compiled when the task and parent module * are not present. */ #ifndef HAS_TASK_CHIPSET #undef CONFIG_AP_HANG_DETECT #undef CONFIG_CHIPSET_APOLLOLAKE #undef CONFIG_CHIPSET_BRASWELL #undef CONFIG_CHIPSET_CANNONLAKE #undef CONFIG_CHIPSET_GEMINILAKE #undef CONFIG_CHIPSET_MEDIATEK #undef CONFIG_CHIPSET_RK3399 #undef CONFIG_CHIPSET_ROCKCHIP #undef CONFIG_CHIPSET_SKYLAKE #undef CONFIG_CHIPSET_STONEY #undef CONFIG_POWER_COMMON #undef CONFIG_POWER_TRACK_HOST_SLEEP_STATE #endif #ifndef HAS_TASK_KEYPROTO #undef CONFIG_KEYBOARD_PROTOCOL_8042 /* * Note that we don't undef CONFIG_KEYBOARD_PROTOCOL_MKBP, because it doesn't * have its own task. */ #endif #ifndef HAS_TASK_PDCMD #undef CONFIG_HOSTCMD_PD #endif /* Certain console cmds are irrelevant without parent modules. */ #ifndef CONFIG_BATTERY #undef CONFIG_CMD_PWR_AVG #endif #ifndef CONFIG_ADC #undef CONFIG_CMD_ADC #endif /*****************************************************************************/ /* Define derived Chipset configs */ #if defined(CONFIG_CHIPSET_APOLLOLAKE) || \ defined(CONFIG_CHIPSET_GEMINILAKE) #define CONFIG_CHIPSET_APL_GLK #endif /*****************************************************************************/ /* * Apply test config overrides last, since tests need to override some of the * config flags in non-standard ways to mock only parts of the system. */ #include "test_config.h" /* * Sanity checks to make sure some of the configs above make sense. */ #if (CONFIG_AUX_TIMER_PERIOD_MS) < ((HOOK_TICK_INTERVAL_MS) * 2) #error "CONFIG_AUX_TIMER_PERIOD_MS must be at least 2x HOOK_TICK_INTERVAL_MS" #endif #ifdef CONFIG_USB_SERIALNO #define CONFIG_SERIALNO_LEN 28 #endif #ifndef CONFIG_EC_MAX_SENSOR_FREQ_MILLIHZ #define CONFIG_EC_MAX_SENSOR_FREQ_MILLIHZ \ CONFIG_EC_MAX_SENSOR_FREQ_DEFAULT_MILLIHZ #endif #endif /* __CROS_EC_CONFIG_H */