# EC Acronyms and Technologies ## Glossary * **8042 Interface**{#8042} Interface for sending keyboard events to the [AP](#ap) and for receiving commands from the AP. Only supported by x86 based APs. * **ACCEL - Accelerometer**{#accel} A sensor that measures acceleration, typically over 3-axis. Nominally provides information about the orientation of a device. On Chromebook 2-in-1 devices, there is an accelerometer in the base and one in the lid. Combining the measurements from both accelerometers allows for a precise calculation of the lid angle, used to switch between tablet and laptop mode. * **ACCELGYRO - Accelerometer/Gyroscope**{#accelgyro} A combination [accelerometer](#accel) and [gyroscope](#gyro) sensor that provides more precise orientation information by measuring both linear and rotational motion. * **ADC - Analog to Digital Converter**{#adc} A sensor that converts an analog voltage to a digital reading. * **ALS - Ambient Light Sensor**{#als} A sensor that measures the ambient light present. Used to automatically control the screen and keyboard backlight level. * **AP - Application Processor**{#ap} The processor on the board that boots and runs ChromeOS. * **BAR - Barometer**{#bar} A sensor that measures atmospheric pressure. * **BC12 - Battery Charging**{#bc12} A device that implements the USB Battery Charging specification, version 1.2. The complete [BC 1.2 Specification] is available from the USB Implementers Forum. * **CBI - CROS Board Information**{#cbi} A collection of properties describing the board. This includes board version, SKU, model name, and other fields. More details are found in the [CrOS Board Info] documentation. * **CEC - Consumer Electronics Control**{#cec} A one-wire bidirectional bus. More details are on the [CEC Wikipedia page]. * **DPTF - Dynamic Power and Thermal Framework (Intel)**{#dptf} Intel's platform based power and thermal management. See the [DPTF Readme] for details on the implementation used in ChromeOS. * **EC - Embedded Controller**{#ec} The [MCU](#mcu) used to control the keyboard, battery charging, USB port switching, sensor management, and other functions, offloading these tasks from the [AP](#ap). * **eSPI - Enhanced Serial Peripheral Interface (Intel)**{#espi} Intel's synchronous communication interface between the [AP](#ap) and the [EC](#ec). Supports quad I/O mode and clock speeds up to 66 Mhz, providing bandwidth up to 264 Mbps. The full [eSPI Specification] is available from Intel. * **GPIO - General Purpose Input/Output**{#gpio} An individual signal that can independently controlled and read. GPIOs are used to enable/disable power rails, drive reset signals, and receive interrupts from devices connected to the EC. GPIOs may also be connected to [I/O expanders](#ioexpander). * **GYRO - Gyroscope**{#gyro} A sensor that measures angular momentum, providing information about rotational motion of the device. * **I/O Expander**{#ioexpander} An [I2C](#i2c) slave device that provides additional GPIO signals (anywhere from 8 - 32 signals). GPIOs behind an I/O expander are written and read using I2C register accesses from the I2C master. * **I2C - Inter-Integrated Circuit**{#i2c} A 2-wire synchronous communication bus, consisting of a clock signal and a bidirectional data signal. An I2C bus typically contains one master device and one more slave devices. The I2C standard defines supported clock speeds of 100 KHz and 400 KHz. The full [I2C Specification] is available from NXP (formerly Phillips). * **LPC - Low Pin Count bus**{#lpc} Legacy communication bus between the [AP](#ap) and [EC](#ec). Runs at 33 MHz, providing a 133 Mbps bandwidth connection. Replaced by the [eSPI](#espi) interface. * **MAG - Magnetometer**{#mag} A digital compass sensor, providing orientation for navigation. * **MCU - Microcontroller Unit**{#mcu} A small integrated chip containing a CPU core, on-chip ROM, on-chip RAM. Also contains multiple peripheral interfaces, including GPIO, I2C buses, SPI buses, ADC, PWM, etc. * **MKBP - Matrix Keyboard Protocol**{#mkbp} Message based protocol for communicating asynchronous events from the [EC](#ec) to the [AP](#ap). Events are not limited to keyboard events with the sensor subsystem as one of the main users. An EC board implementation can be configured to send keyboard events through MKBP or using the [8042 interface](#8042). This is the [EC MKBP driver] implementation. * **MST - Multi Stream Transport**{#mst} Part of the Display Port 1.2 standard, used to drive multiple independent video streams from a single display port. The EC code is typically responsible for enabling and disabling the MST hub chipset. * **PD - USB Power Delivery**{#pd} See the [USB-C documentation](./usb-c.md#pd) for more details. * **PMIC - Power Management IC**{#pmic} An integrated circuit used to turn power rails on and off. * **PPC - USB Power Path Controller**{#ppc} See the [USB-C documentation](./usb-c.md#ppc) for more details. * **PWM - Pulse Width Modulation**{#pwm} Method of varying the duty cycle of a signal to control another device. A typical application is to control fan speeds or the brightness of a backlight. * **SPI - Serial Peripheral Interconnect**{#spi} A 4-wire synchronous communication bus consisting of the signals CLK (clock), MOSI (master-out-slave-in), MISO (master-in-slave-out), and CS (chip-select, one per SPI slave). Clock speeds over 100 MHz are supported. Communication involves a SPI frame, consisting of the assertion of chip select, transmitting one or more bytes on the MOSI signal, receiving zero or more bytes on the MISO signal, and de-assertion of the chip select. The contents of a SPI frame varies based on the SPI slave type. * **SVDM - Structured Vendor Defined Messages**{#svdm} See the [USB-C documentation](./usb-c.md#svdm) for more details. * **TCPC - USB Type-C Port Controller**{#tcpc} See the [USB-C documentation](./usb-c.md#tcpc) for more details. * **UART - Universal Asynchronous Receiver Transceiver**{#uart} Also known as a serial port. An asynchronous communication channel between two devices with a dedicated receive pin, transmit pin, and ground. Optional hardware flow control signals require additional connections between the devices. Standard transmission rates are slow (up to 115200 bits per second). Typical use is to provide a debug console to the EC. [RS-232] is the protocol standard used by UARTs. [BC 1.2 Specification]: [CrOS Board Info]: [CEC Wikipedia page]: [DPTF Readme]: [eSPI Specification]: [I2C Specification]: [RS-232]: [EC MKBP driver]: