/* -*- mode:c -*-
 *
 * Copyright 2015 The Chromium OS Authors. All rights reserved.
 * Use of this source code is governed by a BSD-style license that can be
 * found in the LICENSE file.
 */

/* Declare symbolic names for all the GPIOs that we care about.
 * Note: Those with interrupt handlers must be declared first. */

/* Interrupts */
GPIO_INT(USB_C0_VBUS_WAKE_L,     PIN(C, 14),  GPIO_INT_BOTH,    pd_vbus_evt_p0)
GPIO_INT(USB_C1_VBUS_WAKE_L,     PIN(C, 15),  GPIO_INT_BOTH,    pd_vbus_evt_p1)

/*
 * Older boards have A13 connected to a test point with no PU / PD, so we must
 * enable an internal PU.
 * Newer boards have A13 connected to 3.3V / GND through a 100K resistor, so
 * we must not enable an internal PU. All MP boards will use the newer config.
 * TODO(crosbug.com/p/50518): Remove CONFIG_SYSTEM_UNLOCKED prior to building
 * MP FW.
 */
#ifdef CONFIG_SYSTEM_UNLOCKED
GPIO_INT(WP_L,               PIN(A, 13), GPIO_INT_BOTH | GPIO_PULL_UP,
         switch_interrupt)
#else
GPIO_INT(WP_L,               PIN(A, 13), GPIO_INT_BOTH, switch_interrupt)
#endif

/* PD RX/TX */
GPIO(USB_C0_CC1_PD,          PIN(A, 2),  GPIO_ANALOG)
GPIO(USB_C_REF,              PIN(A, 1),  GPIO_ANALOG)
GPIO(USB_C1_CC1_PD,          PIN(A, 0),  GPIO_ANALOG)
GPIO(USB_C0_CC2_PD,          PIN(A, 4),  GPIO_ANALOG)
GPIO(USB_C1_CC2_PD,          PIN(A, 5),  GPIO_ANALOG)

GPIO(USB_C1_CCX_TX_DATA,     PIN(B, 14), GPIO_INPUT)
GPIO(USB_C0_CC1_TX_DATA,     PIN(B, 4),  GPIO_INPUT)
GPIO(USB_C1_CC2_TX_SEL,      PIN(B, 0),  GPIO_OUT_LOW) /* C1_CC2_TX_SEL */
GPIO(USB_C0_CC2_TX_DATA,     PIN(A, 6),  GPIO_INPUT)
GPIO(USB_PD_VBUS_WAKE,       PIN(C, 13), GPIO_INPUT)

GPIO(PP3300_USB_PD_EN,       PIN(A, 15), GPIO_OUT_HIGH)
GPIO(USB_C0_CC1_VCONN1_EN,   PIN(B, 1),  GPIO_OUT_LOW)
GPIO(USB_C0_CC2_VCONN1_EN,   PIN(B, 2),  GPIO_OUT_LOW)
GPIO(USB_C1_CC1_VCONN1_EN,   PIN(B, 9),  GPIO_OUT_LOW)
GPIO(USB_C1_CC2_VCONN1_EN,   PIN(F, 0),  GPIO_OUT_LOW)

GPIO(USB_C0_HOST_HIGH,       PIN(A, 3),  GPIO_OUT_LOW)
GPIO(USB_C1_HOST_HIGH,       PIN(A, 7),  GPIO_OUT_LOW)
GPIO(USB_C0_CC1_ODL,         PIN(A, 11), GPIO_ODR_LOW)
GPIO(USB_C0_CC2_ODL,         PIN(A, 12), GPIO_ODR_LOW)
GPIO(USB_C1_CC1_ODL,         PIN(B, 12), GPIO_ODR_LOW)
GPIO(USB_C1_CC2_ODL,         PIN(A, 8),  GPIO_ODR_LOW)

/*
 * I2C pins should be configured as inputs until I2C module is
 * initialized. This will avoid driving the lines unintentionally.
 */
GPIO(SLAVE_I2C_SCL,          PIN(B, 6),  GPIO_INPUT)
GPIO(SLAVE_I2C_SDA,          PIN(B, 7),  GPIO_INPUT)

#ifdef BOARD_OAK_PD
GPIO(EC_INT,                 PIN(B, 5),  GPIO_OUT_HIGH)
#else
GPIO(EC_INT,                 PIN(A, 14), GPIO_ODR_HIGH)
#endif

UNIMPLEMENTED(ENTERING_RW)

#if 0
/* Alternate functions */
GPIO(USB_C1_TX_CLKOUT,       PIN(B, 15), GPIO_OUT_LOW)
GPIO(USB_C0_TX_CLKOUT,       PIN(B, 8),  GPIO_OUT_LOW)
GPIO(USB_C1_TX_CLKIN,        PIN(B, 13), GPIO_OUT_LOW)
GPIO(USB_C0_TX_CLKIN,        PIN(B, 3),  GPIO_OUT_LOW)
#endif

ALTERNATE(PIN_MASK(B, 0x0008), 0, MODULE_USB_PD, 0) /* SPI1: SCK(PB3) */
ALTERNATE(PIN_MASK(B, 0x2000), 0, MODULE_USB_PD, 0) /* SPI2: SCK(PB13) */
ALTERNATE(PIN_MASK(B, 0x0100), 2, MODULE_USB_PD, 0) /* TIM16_CH1: PB8   */
ALTERNATE(PIN_MASK(B, 0x8000), 1, MODULE_USB_PD, 0) /* TIM15_CH2: PB15  */
ALTERNATE(PIN_MASK(A, 0x0600), 1, MODULE_UART,   0) /* USART1: PA9/PA10 */
ALTERNATE(PIN_MASK(B, 0x00c0), 1, MODULE_I2C,    0) /* I2C SLAVE:PB6/7  */