/* Copyright 2018 The Chromium OS Authors. All rights reserved.
 * Use of this source code is governed by a BSD-style license that can be
 * found in the LICENSE file.
 */

/* Cheza board configuration */

#ifndef __CROS_EC_BOARD_H
#define __CROS_EC_BOARD_H

/* TODO(waihong): Remove the following bringup features */
#define CONFIG_BRINGUP
#define CONFIG_SYSTEM_UNLOCKED /* Allow dangerous commands. */
#define CONFIG_USB_PD_DEBUG_LEVEL 3
#define CONFIG_CMD_AP_RESET_LOG
#define CONFIG_HOSTCMD_AP_RESET

/*
 * By default, enable all console messages excepted event and HC:
 * The sensor stack is generating a lot of activity.
 * They can be enabled through the console command 'chan'.
 */
#define CC_DEFAULT     (CC_ALL & ~(CC_MASK(CC_EVENTS) | CC_MASK(CC_HOSTCMD)))

/* NPCX7 config */
#define NPCX_UART_MODULE2 1  /* GPIO64/65 are used as UART pins. */
#define NPCX_TACH_SEL2    0  /* No tach. */
#define NPCX7_PWM1_SEL    0  /* GPIO C2 is not used as PWM1. */

/* Internal SPI flash on NPCX7 */
#define CONFIG_FLASH_SIZE (1024 * 1024)  /* 1MB internal spi flash */
#define CONFIG_SPI_FLASH_REGS
#define CONFIG_SPI_FLASH_W25Q80 /* Internal SPI flash type. */
#define CONFIG_HOSTCMD_FLASH_SPI_INFO

/* EC Modules */
#define CONFIG_I2C
#define CONFIG_I2C_MASTER
#define CONFIG_LED_COMMON
#define CONFIG_LOW_POWER_IDLE
#define CONFIG_ADC
#define CONFIG_BACKLIGHT_LID
#define CONFIG_FPU
#define CONFIG_PWM
#define CONFIG_PWM_DISPLIGHT

#define CONFIG_VBOOT_HASH

#define CONFIG_DETACHABLE_BASE

#undef CONFIG_PECI

#define CONFIG_HOSTCMD_SPS
#define CONFIG_HOST_COMMAND_STATUS
#define CONFIG_HOSTCMD_SECTION_SORTED /* Host commands are sorted. */
#define CONFIG_MKBP_EVENT
#define CONFIG_KEYBOARD_PROTOCOL_MKBP
#define CONFIG_MKBP_USE_GPIO

#define CONFIG_BOARD_VERSION_GPIO
#define CONFIG_POWER_BUTTON
#define CONFIG_VOLUME_BUTTONS
#define CONFIG_BUTTON_TRIGGERED_RECOVERY
#define CONFIG_EMULATED_SYSRQ
#define CONFIG_CMD_BUTTON
#define CONFIG_SWITCH
#define CONFIG_LID_SWITCH
#define CONFIG_EXTPOWER_GPIO

#define CONFIG_TABLET_MODE
#define CONFIG_TABLET_MODE_SWITCH

/* Battery */
#define CONFIG_BATTERY_CUT_OFF
#define CONFIG_BATTERY_PRESENT_GPIO GPIO_BATT_PRES_ODL
#define CONFIG_BATTERY_SMART

/* Charger */
#define CONFIG_CHARGER
#define CONFIG_CHARGER_V2
#define CONFIG_CHARGE_MANAGER
#define CONFIG_CHARGER_ISL9238
#define CONFIG_CHARGE_RAMP_HW
#define CONFIG_USB_CHARGER
#define CONFIG_CMD_CHARGER_ADC_AMON_BMON
#define CONFIG_CHARGER_PSYS
#define CONFIG_CHARGER_PSYS_READ
#define CONFIG_CHARGER_DISCHARGE_ON_AC

/* TODO(b/79163120): Use correct charger values, copied from Lux for rev-0 */
#define CONFIG_CHARGER_INPUT_CURRENT 512
#define CONFIG_CHARGER_MIN_BAT_PCT_FOR_POWER_ON 2
#define CONFIG_CHARGER_MIN_POWER_MW_FOR_POWER_ON 7500
#define CONFIG_CHARGER_SENSE_RESISTOR 10
#define CONFIG_CHARGER_SENSE_RESISTOR_AC 20

/* BC 1.2 Charger */
#define CONFIG_BC12_DETECT_PI3USB9281
#define CONFIG_BC12_DETECT_PI3USB9281_CHIP_COUNT 2

/* USB */
#define CONFIG_USB_POWER_DELIVERY
#define CONFIG_CMD_PD_CONTROL
#define CONFIG_USB_PD_ALT_MODE
#define CONFIG_USB_PD_ALT_MODE_DFP
#define CONFIG_USB_PD_DISCHARGE_PPC
#define CONFIG_USB_PD_DUAL_ROLE
#define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE
#define CONFIG_USB_PD_LOGGING
#define CONFIG_USB_PD_MAX_SINGLE_SOURCE_CURRENT TYPEC_RP_3A0
#define CONFIG_USB_PD_PORT_COUNT 2
#define CONFIG_USB_PD_TCPC_LOW_POWER
#define CONFIG_USB_PD_TCPM_ANX3429
#define CONFIG_USB_PD_TCPM_PS8751
#define CONFIG_USB_PD_TCPM_MUX
#define CONFIG_USB_PD_TCPM_TCPCI
#define CONFIG_USB_PD_TRY_SRC
#define CONFIG_USB_PD_VBUS_DETECT_CHARGER
#define CONFIG_USB_PD_5V_EN_CUSTOM
#define CONFIG_USB_MUX_VIRTUAL
#define CONFIG_USBC_PPC_SN5S330
#define CONFIG_USBC_SS_MUX
#define CONFIG_USBC_VCONN
#define CONFIG_USBC_VCONN_SWAP

/* RTC */
#define CONFIG_CMD_RTC
#define CONFIG_HOSTCMD_RTC

/* Sensors */
#define CONFIG_ACCELGYRO_BMI160
#define CONFIG_ACCEL_INTERRUPTS
#define CONFIG_ACCELGYRO_BMI160_INT_EVENT TASK_EVENT_CUSTOM(4)
#define CONFIG_ACCEL_FIFO 512
#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO / 3)
#define CONFIG_CMD_ACCELS
#define CONFIG_CMD_ACCEL_INFO

/* TODO(b/79163120): Use correct PD delay values, copied from Lux for rev-0 */
#define PD_POWER_SUPPLY_TURN_ON_DELAY   30000  /* us */
#define PD_POWER_SUPPLY_TURN_OFF_DELAY  250000 /* us */
#define PD_VCONN_SWAP_DELAY             5000 /* us */

/* TODO(b/79163120): Use correct PD power values, copied from Lux for rev-0 */
#define PD_OPERATING_POWER_MW   15000
#define PD_MAX_POWER_MW         45000
#define PD_MAX_CURRENT_MA       3000
#define PD_MAX_VOLTAGE_MV       20000

#define CONFIG_CHIPSET_SDM845
#define CONFIG_CHIPSET_RESET_HOOK
#define CONFIG_POWER_COMMON
#define CONFIG_POWER_PP5000_CONTROL

/* NPCX Features */
#define CONFIG_HIBERNATE_PSL

/* I2C Ports */
#define I2C_PORT_BATTERY I2C_PORT_POWER
#define I2C_PORT_CHARGER I2C_PORT_POWER
#define I2C_PORT_ACCEL   I2C_PORT_SENSOR
#define I2C_PORT_POWER   NPCX_I2C_PORT0_0
#define I2C_PORT_TCPC0   NPCX_I2C_PORT1_0
#define I2C_PORT_TCPC1   NPCX_I2C_PORT2_0
#define I2C_PORT_EEPROM  NPCX_I2C_PORT5_0
#define I2C_PORT_SENSOR  NPCX_I2C_PORT7_0

#ifndef __ASSEMBLER__

#include "gpio_signal.h"
#include "registers.h"

enum power_signal {
	SDM845_AP_RST_L = 0,
	SDM845_PS_HOLD,
	SDM845_PMIC_FAULT_L,
	SDM845_POWER_GOOD,
	SDM845_WARM_RESET,
	/* Number of power signals */
	POWER_SIGNAL_COUNT
};

enum adc_channel {
	ADC_BASE_DET,
	ADC_VBUS,
	ADC_AMON_BMON,
	ADC_PSYS,
	ADC_CH_COUNT
};

/* Motion sensors */
enum sensor_id {
	LID_ACCEL = 0,
	LID_GYRO,
};

enum pwm_channel {
	PWM_CH_DISPLIGHT,
	PWM_CH_COUNT
};

/* Custom function to indicate if sourcing VBUS */
int board_is_sourcing_vbus(int port);
/* Enable VBUS sink for a given port */
int board_vbus_sink_enable(int port, int enable);
/* Reset all TCPCs. */
void board_reset_pd_mcu(void);
/* Base detection interrupt handler */
void base_detect_interrupt(enum gpio_signal signal);

#endif /* !defined(__ASSEMBLER__) */

#endif /* __CROS_EC_BOARD_H */